Posts: 3,390
Threads: 1
Joined: Jan 2002
Pretty sure I'm stuck sanding it down but thought I'd ask first, just in case.
I applied water based dye stain to white oak and it turned out way too dark. (I did a sample board but I obviously must've gone way heavier on the actual table top) Is there anything I can do to lighten it? It's been on there since last night.
-Marc
-Marc
Posts: 12,878
Threads: 0
Joined: Jan 2010
Location: Lewiston, NY
You should be able to remove some of the dye by repeatably wiping it with a wet sponge. If that doesn't work, household bleach should lighten or completely remove it. I would try that on some scrap first to make sure it doesn't cause any problems.
John
Posts: 3,390
Threads: 1
Joined: Jan 2002
Thanks for the tips. If I tried bleach do I need to do anything afterwards to neutralize it before I either re-stain or top coat?
-Marc
Posts: 8,963
Threads: 0
Joined: Sep 2010
Just rinse really well. If the bleach doesn't do it you can try oxalic acid AKA bartenders friend. If you used transtint the water will do the trick.
homo homini lupus
"The best lack all conviction, while the worst are full of passionate intensity." Yeats
Si vis pacem, para bellum
Quodcumque potest manus tua facere instaner opere Ecclesiastes
Posts: 3,390
Threads: 1
Joined: Jan 2002
No it was a General Finishes can.
-Marc
Posts: 19,681
Threads: 0
Joined: Aug 2001
You can remove or greatly lighten dye stain by using a chlorine bleach. Swimming pool chlorine will work but it's a little slow.
Do not use Oxalic Acid which is sometime sold as "wood bleach". Oxalic acid is a bleach used to remove or lighten mineal stains but it will further set a dye stain.
Howie.........
Posts: 7,421
Threads: 1
Joined: Sep 2005
Oxalic acid is traditionally used to bleach wood, but that will lighten the color of the wood itself as well as the stain.
Bleach and the rinse will raise the grain and you will have to sand that down again.
You might try wiping with a solvent that won't raise the grain. I think alcohol will work. The die will dissolve in alcohol and I don't believe alcohol will raise the grain. So I would try to wipe down with that.
Mineral spirits might be a good alternative too, but I prefer alcohol.
No animals were injured or killed in the production of this post.
Posts: 3,390
Threads: 1
Joined: Jan 2002
Okay so I gave it a good scrubbing with DNA tonight and it worked pretty well. I think I'll leave it alone without hitting it with the bleach.
Thanks for the tips. It was certainly much better than sanding the whole thing down!
-Marc
Posts: 7,421
Threads: 1
Joined: Sep 2005
If you want to get it still lighter try flooding the surface (use a foam brush) and letting it soak in for a few minutes and then wipe down again. It might get as some of the deeper surfaces and release more of the dye.
No animals were injured or killed in the production of this post.
Posts: 19,681
Threads: 0
Joined: Aug 2001
You might want to google "wood bleach". You will find a number of articles there -- including one by Jeff Jewitt. The articles describe the three bleaches used in wood finishing. All the articles describle the three woodworking bleaches and coloring they will affect.
As I described above, chlorine bleach is used to remove dye coloring from wood, Oxalic acid is unique in that it will remove mineral stains from iron and iron oxide caused by moisture contact between iron and the tannin is certain woods without changing the color of the wood. Finally is oxygen two--part A/B bleach. This bleach will lighten or remove the natural color of the wood.
Both Bob Flexner's and Jeff Jewitt's books describe the bleaches when and how they should be used.
Howie.........
