Questions for the spoon carvers
#10
We had to do a bit of tree trimming this week, and I ended up with a couple of small Bradford Pear branches to try some spoon carving with.

Couple of questions...assuming I get to carving in short order, how much do they need to dry before they can be considered finished and/or usable?

Does one apply any sort of oil or finish for use in the kitchen?

Thanks

David
Dave Arbuckle was kind enough to create a Sketchup model of my WorkMate benchtop: http://www.arbolloco.com/sketchup/MauleSkinnerBenchtop.skp
Reply
#11
I'm fare from bein a spooncraver, but made a few (years
ago). It is easier to shape them wile the wood is wet.

For the last finishing cut I'd let them dry after shaping, wich
is fast because they are thin.

This has worked for me on a few spoons of swedish
juniper. Not sure if that works on other woods.

BTW dou you use the inside of the treee to become
the upper side of the spoon or the lower side?

Cheers

Pedder
Reply
#12
A good soaking of flax seed oil, or similar. My son rigged up a capped 4" pvc pipe to hold the oil while the spoon soaks.
Reply
#13
Green is always better than dry. Air dried will cut better than kiln dried. I made a spoon from some almond a couple of years ago. Wood was green and it shaped marvelously. There's a tendency to spit on the ends. I soaked mine in mineral oil. No issues since. I didn't rough it out and then finish it. I did it all at once. Steve (Bibliophile) will chime in soon. I consider him the forum's spoon expert.
Still Learning,

Allan Hill
Reply
#14
MauleSkinner said:


We had to do a bit of tree trimming this week, and I ended up with a couple of small Bradford Pear branches to try some spoon carving with.

Couple of questions...assuming I get to carving in short order, how much do they need to dry before they can be considered finished and/or usable?

They will be used in liquids and wet environments, so three/four days to surface dry. Any more a waste of time on a user. For show, not go, week or ten.

Does one apply any sort of oil or finish for use in the kitchen?

I do. Walnut oil after surface is dry, to refusal, wipe after ten minutes, and cure a week. Slows the uptake of the food colors a bit. Don't like the smell of linseed (flaxseed) or tung, though both have proponents.

Thanks

David


Better to follow the leader than the pack. Less to step in.
Reply
#15
If you're lap-carving with a hook knife and a straight knife, by all means shape them while green. You can keep them from drying out for a bit by putting them in a plastic bag.

You'll want to split them, of course, and remove the pith before carving.

Once you've shaped the spoon, you can let it rest a few days to let the surface dry before finishing, but there's nothing inherently dangerous about finishing them immediately, letting the finish cure, and putting them right to work in the kitchen.

If you plan to carve them at the bench with a gouge and spokeshave, you can rough the spoons out green, but you'll want to leave them sit a couple days until the surface is dry to the touch before you do a final shaping/scraping/sanding. Scrapers and sandpaper don't like wet wood.
Steve S.
------------------------------------------------------
Tradition cannot be inherited, and if you want it you must obtain it by great labour.
- T. S. Eliot

Tutorials and Build-Alongs at The Literary Workshop
Reply
#16
Quote:

It is easier to shape them wile the wood is wet.




And carving will be easier on dry wood if you spray it first with a 1/3 rubbing alcohol and 2/3 water..
Often Tested.    Always Faithful.      Brothers Forever

Jack Edgar, Sgt. U.S. Marines, Korea, America's Forgotten War
Get off my lawn !
Upset





Reply
#17
Thanks for that tip. We have much more birch and pear and maple and hickory and apricot, etc, laying around turning to stone, than we have time to work it.

Eric
Reply
#18
Thanks for the replies...that helps a lot.

David
Dave Arbuckle was kind enough to create a Sketchup model of my WorkMate benchtop: http://www.arbolloco.com/sketchup/MauleSkinnerBenchtop.skp
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.