Posts: 767
Threads: 0
Joined: May 2006
Hello,
I have a tool cabinet with a flat metal top, and I'd like to have a piece of 3/4 MDF glued to the top, so as to have a MDF work surface. The top is about 18x24.
What if anything, would you recommend that I use to do this?
Thanks,
Louis
Posts: 2,274
Threads: 90
Joined: Jun 2001
Actually I wouldn't glue it. I would attach it with screws from underneath.
John
Always use the right tool for the job.
We need to clean house.
Posts: 767
Threads: 0
Joined: May 2006
Thanks. That's my other alternative, but I'd rather glue it if possible, because I want a smooth result. I know that I could countersink the screws and even attach Masonite on top of that, but I would prefer to glue it if I can.
Louis
Posts: 22,712
Threads: 0
Joined: Feb 2005
Location: Regina Saskatchewan Canada
Plain old silicone or acrylic latex caulk. A series of thin s curving beads and set it in place. Weight the top for 24 hours. It doesn't really need the weight to bond but it will keep you from fooling with it until the adhesive sets up.
Blackhat
Bad experiences come from poor decisions. So do good stories.
Posts: 5,119
Threads: 12
Joined: Apr 2009
Location: SoMar
Gorilla glue will handle that sticky situation for you.
Posts: 20,866
Threads: 1
Joined: Sep 2003
Location: Sioux Falls SD
I used recessed self drilling & tapping screws at the outer edge of the top penetrating the metal where there was no drawer below. This kept me from having to get inside to place a nut or drive a screw.
WoodNET... the new safespace
Posts: 14,947
Threads: 0
Joined: May 2005
Location: Oklahoma
Reconsider the screws so the top can be replaced as needed.
Carolyn
Trip Blog for Twelve Countries: [url=http://www.woodworkingtraveler.wordpress.com[/url]
"It's good to know, but it's better to understand." Auze Jackson
Posts: 18,980
Threads: 0
Joined: Jul 2002
Location: Ohio
MsNomer said:
Reconsider the screws so the top can be replaced as needed.
That is what I'd do. And note that the suggestion from John was to screw from below...so you wouldnt have a problem with screws on the surface.
Posts: 7,421
Threads: 1
Joined: Sep 2005
Silicone glue will work, but I would use double faced foam tape. 3M makes many grades, some with extraordinary hold. And when you decide to remove it, a hair dryer will get rid of the residue. Removing silicone adhesive (or E6000, a stronger flexible adhesive) will be very difficult.
I would also use carpet tape to attach a piece of tempered hardboard as a sacrificial work surface above the MDF. It is a much harder surface than MDF and it is very cheap. Carpet tape is not very strong but it is fine for this application.
No animals were injured or killed in the production of this post.
Posts: 31,110
Threads: 2
Joined: Mar 2003
Location: Athens, TN
I'm also in the non-permanent camp.
The double stick tape idea has merit, but bolting is best. Provide, of course, you have access.
To do so without visible fasteners, I'd drill the steel deck, then mark the hole locations on the bottom of the mdf top.
Remove the mdf top and embed hardwood plugs at the screw locations, then just use screws.
However, I would probably just use flathead fasteners in the 4 corners and leave the fasteners exposed. What would they hurt?
Rocket Science is more fun when you actually have rockets.
"The Constitution is not an instrument for the government to restrain the people, it is an instrument for the people to restrain the government." -- Patrick Henry
