Posts: 24,682
Threads: 1
Joined: Jul 2002
Location: St Boni, MN
I was using a bowl bit with a template when the guide bearing seized. This makes for a very interesting experience in Maple. The burn marks took a while to sand out.
The bearing was completely seized and had to be driven off the bit. Kind of strange because I just touched up the bit and lubed the bearing a week ago. I've done 2 other bowls since I sharpened the bit and they went fine. Never seen one completely seize up before. It's not a new bit so I can't complain too much.
Mike
If you're the smartest person in the room, you're in the wrong room!
But not today...
Posts: 3,066
Threads: 0
Joined: Jan 2004
What lubrication did you use?
Posts: 20,950
Threads: 0
Joined: May 2005
Bushings never seize.
Better to follow the leader than the pack. Less to step in.
Posts: 24,682
Threads: 1
Joined: Jul 2002
Location: St Boni, MN
(09-22-2016, 07:16 AM)TomFromStLouis Wrote: What lubrication did you use?
Boeshield.
Mike
If you're the smartest person in the room, you're in the wrong room!
But not today...
Posts: 20,381
Threads: 4
Joined: Sep 2007
Location: CinDay
09-22-2016, 05:11 PM
(This post was last modified: 09-22-2016, 05:24 PM by Steve N.)
Wondering if it isn't more about the brand of bit, than the lube? Sounds like a shorts changing type moment
I had a Katana that self destructed, since I've stuck with CMT's or Whiteside's.
Worst thing they can do is cook ya and eat ya
GW
Posts: 24,145
Threads: 2
Joined: Sep 2003
Location: Missouri
I usually stand the bit up in the vise, and put 3-in-one oil on the seal, letting it soak in, occasionally turning the bearing.
Steve
Mo.
I miss the days of using my dinghy with a girlfriend too. Zack Butler-4/18/24
The Revos apparently are designed to clamp railroad ties and pull together horrifically prepared joints
WaterlooMark 02/9/2020
Posts: 13,412
Threads: 0
Joined: Jun 2004
Location: Texas
Related, in the case for motor bearings that soon seize or go bad after oiling, I theorize it isn't the oil that killed the bearing, but the beforehand lack of oil that caused minute particles of metal to form in the bearing where they free flow, but when oil is added, it makes a metallic paste of the particles causing them to gum the bearing up and/or cause more rapid friction and heat and wear.
I have oiled old motors that were running fine (but dry) and they failed soon after. I got to where I wouldn't oil old dry motors.
Boeshield isn't a lubricant for bearings as I understand it, but a metal protectant and leaves a dry waxy film- probably not good for any high speed bearing.
Waxy surfaces will collect dust and debris. A nice regular 20w oil is fine.
Posts: 10,717
Threads: 1
Joined: Jan 2006
Location: Orlando, Florida
(09-22-2016, 03:57 PM)gMike Wrote: Boeshield.
Boeshield is a nice protectant, but a poor lubricant. It has paraffin as an ingredient. If it got hot, then the wax will burn off, leaving you with almost no protection. Likewise, WD40 is a poor choice for bearing lube. 3-in-1 is an OK choice. Rockler and Woodcraft sell purpose-made router bit bearing lubricants. PG2000 is one that comes in a handy tube with a hypo style applicator pen.
Still Learning,
Allan Hill
Posts: 13,485
Threads: 0
Joined: Oct 1999
(09-22-2016, 08:41 AM)MichaelMouse Wrote: Bushings never seize.
While true, that is less than useful.
A bushing ONLY allows for a bowl bit to make a pocket as deep as the bit plus template.
A flush bearing allows the pattern to be cut, then the template can be removed and the bearing can ride on the previously cut wall to whatever depth can be reached. Done this many times.
Posts: 20,950
Threads: 0
Joined: May 2005
09-25-2016, 04:41 PM
(This post was last modified: 09-25-2016, 04:50 PM by MichaelMouse.)
Take away the template and use the new opening. Get you a few more mm without the template.
For those of us using "bowl" bits as sort of oversize core box on trays, extremely useful to not worry about bearings.
Better to follow the leader than the pack. Less to step in.
