Posts: 13,416
Threads: 4
Joined: Jun 2007
Location: New Jersey
I have an otherwise great performing D-7 handsaw, but it has the annoying habit of vibrating at the toe when in use. Now, that could be the result of bad technique, but I'm a pretty good sawyer, and my other saws don't have this characteristic. I know saws are tensioned by hammer and anvil, and while I've read Bob Smalzer's articles over at WKFine tools, I've been unable to find any other resources explaining the technique, which takes a fair amount of skill. Anybody have any leads?
Credo Elvem ipsum etiam vivere
Non impediti ratione cogitationis
Posts: 4,333
Threads: 0
Joined: Dec 2006
Location: On my own Ignore List
I would PM Darryl Weir, who is the best saw technician I know of. Forrest still hand tensions their circular saw blades, so the craft is not yet dead.
Posts: 57
Threads: 0
Joined: Jul 2008
Location: Cincinnati
Would definitely be interested to hear more about this if you find any good resources or nuggets from someone like Darryl.
Posts: 479
Threads: 0
Joined: Jul 2004
That's kinda weird because I have a D-7 that does the same thing. I always assumed it was because I don't have enough set, but maybe there is more to it. Can't wait to see what you find out.
Posts: 3,017
Threads: 1
Joined: Aug 2009
Maybe it's telling you that its real ambition is to be a musical saw:
like this one!
Don't thwart its dreams!
Posts: 1,501
Threads: 0
Joined: Feb 2007
Can you measure the amount of set. More often the reason for the chatter, IMHO.
Cheers
Pedder
Posts: 13,416
Threads: 4
Joined: Jun 2007
Location: New Jersey
Peddler, that's the first thing I checked, it's properly set, which is why I think it's a tension issue.
Credo Elvem ipsum etiam vivere
Non impediti ratione cogitationis
Posts: 1,694
Threads: 0
Joined: Feb 2011
Ron Herman shows a reasonable example of tension tuning on one of his videos. I used his method on the last full size rip saw I made. Tapping the spine etc. from time to time with my finger and listening to the ring to gauge the amount of tension. Just don't hit the plate hard or you will distort the plate. :
Best wishes
BontzSawWorks.net
Posts: 223
Threads: 0
Joined: Jun 2008
Location: Lowell, MI
I have heard this complaint for sometime and I notice it myself occasionally.
The sides of the teeth contact the side of the kerf in both the cutting stroke as well as the return stroke. At the tooth line there is still a little friction in both directions. Because of this friction, the teeth will setup a vibration in the plate on the return stroke and that is what gets the blade vibrating. The further you retract the saw on the return stroke you put the blade in tension above the board and that concentrates the vibration in the tip that is not engaged below the board.
Some saws do it more than others. I would think that a poorly set would contribute to this. Not to much set but and uneven set along the blade would contribute to the issue.
I new Carl Bilderback and he always thought it was a good idea to lift the blade slightly on the return stroke. He aid it cleared the sawdust away from the kerf. It works, try it. It might give you an indication if my theory has any merit.
Also, make sure your stance is good and you keep the saw in line with the cut. Have someone watch you as you cut. Most folks will respond if you give them permission to critique you.
Its more of an annoyance than anything.
Posts: 1,694
Threads: 0
Joined: Feb 2011
Yep, I have heard that one too. Some either use very little set at the toe end or no set. Otherwise +1 to most mentioned above.
BontzSawWorks.net
