Posts: 5,653
Threads: 0
Joined: May 2005
Location: Centre County Pennsylvania
I tore out the walls in my basement because they had been flooded and got mold. They were put in with cut nails. Is there a better way? Was thinking about anchors or the explosive charge nailers.
Posts: 5,653
Threads: 0
Joined: May 2005
Location: Centre County Pennsylvania
11-17-2016, 12:42 PM
(This post was last modified: 11-17-2016, 12:45 PM by EricU.)
also thought about tapcons. Do tapcons work with pressure treated wood? I'm using pressure treated 2x4 for the floor plates
On another note, I guess I have to buy a lifetime supply of galvanized nails for my nailgun. Seems like they only sell them in packages of a million
Posts: 2,199
Threads: 1
Joined: Sep 2003
Location: Maryland
Google Ramset.
You can get them at HD or Amazon. Wear ear protection....
Posts: 1,630
Threads: 0
Joined: Oct 2016
Location: Green & Gold and Red & White country
(11-17-2016, 12:42 PM)EricU Wrote: also thought about tapcons. Do tapcons work with pressure treated wood? I'm using pressure treated 2x4 for the floor plates
On another note, I guess I have to buy a lifetime supply of galvanized nails for my nailgun. Seems like they only sell them in packages of a million
Construction Adhesive with a few anchors of choice. Just make sure they have the proper coating on them for treated lumber.
KNOWLEDGE AND EXPERIENCE EQUALS WISDOM. RMB
The SO asked me today, "what are you going to do to day"? I said "nothing". She said, "that's what you did yesterday"! Me, "Yes love, but I was not finished yet"!!!!!!!!
Posts: 12,889
Threads: 0
Joined: Jan 2010
Location: Lewiston, NY
TapCons work great, just be sure you have a hammer drill to drill the holes. Easy to use and removable if necessary. They make exterior rated ones which work fine with PT lumber.
John
Posts: 10,777
Threads: 0
Joined: Jul 2005
Location: Front seat on the Struggle Bus
(11-17-2016, 01:01 PM)jteneyck Wrote: TapCons work great, just be sure you have a hammer drill to drill the holes. Easy to use and removable if necessary. They make exterior rated ones which work fine with PT lumber.
John
and an Impact driver to put them in......make sure you vacuum or blow out the holes too.
Ed
Posts: 438
Threads: 0
Joined: Sep 2007
I have drilled the holes and then put a piece of weed wacker line in the hole and then driven in a Stainless steel duplex nail. The weed wacker line and nail create a wedge. Somewhere along the way a ended up with a small box of stainless steel duplex nails, no idea where they came from or how i got them but I only use them for basement walls.
I have used tapcons in the past but they always seem to break on me if I try to remove them.
Posts: 5,119
Threads: 12
Joined: Apr 2009
Location: SoMar
3 words. Powder actuated tool.
Posts: 20,866
Threads: 1
Joined: Sep 2003
Location: Sioux Falls SD
Powdered actuated fasterner combined with lots of construction adhesive. Glue... Fasten and let sit for a day till the glue cures... especially on short closet walls. Otherwise you risk loosening the fastener in cracked concrete if you bang on the new framing too early.
WoodNET... the new safespace
Posts: 13,412
Threads: 0
Joined: Jun 2004
Location: Texas
If the wall can't be lifted by any external force as an impact or wind etc, I'll use the ramset. If it is self supporting I'll use good anchors.
I've always wondered where the concrete goes that the nails space takes up?
favorite ways to attach 2x4 to concrete basement floors
