Posts: 2,367
Threads: 0
Joined: Jan 2004
Location: Chicago Burbs
I have a 7-1/4" Makita cordless CS. If I use a speed square to guide the base the blade seems to bind and struggle to cut the wood. If I cut without the square it cuts fine. So I figure the base is out of parallel to the blade, but, I measured it and seems to be OK. Are there any other methods to determine if these are parallel to each other?
Thanks
Posts: 29,152
Threads: 1
Joined: Aug 2002
check the width of the saw kerf and compare that to the blade?
if it is more than say .010" difference I would say the saw plate is out and needs something done.
Let us not seek the Republican Answer , or the Democratic answer. Let us not seek to fix the blame for the past. Let us accept our own responsibility for the future John F. Kennedy
Posts: 2,384
Threads: 0
Joined: Jan 2008
Location: Irving, Tx
I have the same saw and the same problem. Unfortunately the saw was knocked off the work bench. So I know why but I cannot figure out how to adjust other than put it a vise and bend it back.
I hope someone has an answer to help both of us.
"I tried being reasonable..........I didn't like it." Clint Eastwood
Posts: 29,152
Threads: 1
Joined: Aug 2002
(01-13-2017, 06:05 PM)Bill Holt Wrote: I have the same saw and the same problem. Unfortunately the saw was knocked off the work bench. So I know why but I cannot figure out how to adjust other than put it a vise and bend it back.
I hope someone has an answer to help both of us.
Well bending them back on a skil 77 is done by banging them on the opposite corner that it got dropped on
So I think you nailed the solution
Let us not seek the Republican Answer , or the Democratic answer. Let us not seek to fix the blame for the past. Let us accept our own responsibility for the future John F. Kennedy
Posts: 20,381
Threads: 4
Joined: Sep 2007
Location: CinDay
Easiest to believe is the saw plate is whacked. They put them on with spit and bubblegum anymore. The only other thing that can do what you are talking is the arbor is torn loose from the saw body, or somehow bent/deformed. Averages are it's the saw plate. Arbor coming loose would make some noise to a LOT of noise. I think same with bent.
Just a silly thought, make sure the blade is fully on the arbor. Had a POS somebodies B&D circ saw at a Habitat build a few years back, and someone had swedged the arbor nut down tight, to the point it bent the blade. Taking it apart it looked like they snagged it up on the threads, and the blade didn't fully seat. That was one wild circ saw, but it would fully rotate, just cut very poorly
Worst thing they can do is cook ya and eat ya
GW
Posts: 2,331
Threads: 0
Joined: Dec 2006
Location: virginia beach VA
Mbg, to measure parallel, it would help to have a straight edge, hold it up against the blade so that it clears the teeth, then measure between the straight edge and the base. That should give you a good idea if it is out. If it is out, my guess is that you will have to hammer near one of the connection pins to get it back into alignment.
Posts: 4,444
Threads: 0
Joined: Jan 2005
The saw base is not parallel to the blade. Joe Grout's suggestion will work. Another way to overcome this if the base does not square up entirely is to add a extension to the edge of the base. We had a PC saw ,quite old with a flat base. No turn up on the edges , it was out of square to much to bang around. I guess it was dropped from a distance. An aluminum angle was screwed to the base and parallel to the blade.
mike
Posts: 4,646
Threads: 0
Joined: Jan 2008
im wonderin, checking parallel between saw blade and miter slot on my table saw, I have the blade raised and mark a tooth and measure from same tooth front and back.
wonder if the same should be done on a circ saw for the shoe/base.
