Woodnet Forums › › Active › Tool Swap N' Sell v
WTB Pen Jaws to Fit Noval / Technatool
Thread Modes
WTB Pen Jaws to Fit Noval / Technatool
woodtoolgy Offline
Honored Veteran
Posts: 1,761
Threads: 0
Joined: Jun 2002
#8
02-19-2018, 02:06 PM (This post was last modified: 02-19-2018, 02:07 PM by woodtoolgy.)
I need a pair of Pen Jaws to fit a Nova / Teknatool chuck...  

Anyone got an extra set hanging around?

I'm an unemployed Army Vet... Please advise how much...

Thanks
Slow Dancing..... doing vertically what you're wanting to do horizontally
Find
Reply
crokett™ Offline
Finally Off HoneyBooBoo's list
Posts: 36,547
Threads: 3
Joined: Nov 2004
Location: RTP, NC
#9
02-21-2018, 11:09 AM
PM sent.
Website Find
Reply
crokett™ Offline
Finally Off HoneyBooBoo's list
Posts: 36,547
Threads: 3
Joined: Nov 2004
Location: RTP, NC
#10
02-24-2018, 11:29 AM
Another PM sent, I have other folks interested and if I don't hear anything by Monday will move to the next guy in line.
Website Find
Reply
woodtoolgy Offline
Honored Veteran
Posts: 1,761
Threads: 0
Joined: Jun 2002
#11
02-24-2018, 12:10 PM (This post was last modified: 02-24-2018, 12:11 PM by woodtoolgy.)
(02-24-2018, 11:29 AM)crokett™ Wrote: Another PM sent,  I have other folks interested and if I don't hear anything by Monday will move to the next guy in line.

Thank You... sorry, I thought I responded using my phone...  I don't think these will work as the shanks are shorter than on the pen jaws....
Slow Dancing..... doing vertically what you're wanting to do horizontally
Find
Reply
crokett™ Offline
Finally Off HoneyBooBoo's list
Posts: 36,547
Threads: 3
Joined: Nov 2004
Location: RTP, NC
#12
02-26-2018, 12:28 PM
(02-24-2018, 12:10 PM)woodtoolgy Wrote: Thank You...    sorry, I thought I responded using my phone...  I don't think these will work as the shanks are shorter than on the pen jaws....

I've used these jaws several times to drill pen blanks and similar sized work pieces.   They work just fine.  I have two sets of the jaws and  I have them a set on the lathe right now.  I drilled blanks for a few pens last night.  the pen jaws are shaped differently and are only good for drilling rectangular pen blanks.  they don't have as much surface area for round blanks.   if you don't want them I'll move on.
Website Find
Reply
crokett™ Offline
Finally Off HoneyBooBoo's list
Posts: 36,547
Threads: 3
Joined: Nov 2004
Location: RTP, NC
#13
02-27-2018, 10:05 PM
The pin jaws are gone
Website Find
Reply
woodtoolgy Offline
Honored Veteran
Posts: 1,761
Threads: 0
Joined: Jun 2002
#14
02-28-2018, 10:46 PM
(02-27-2018, 10:05 PM)crokett™ Wrote: The pin jaws are gone

Thank You for getting back to me.   I have a set of the Pin jaws and will give them a try.

Sorry I didn't respond sooner..  I'm unemployed and spend tons of time searching for work...
Slow Dancing..... doing vertically what you're wanting to do horizontally
Find
Reply


Forum Jump:


Users browsing this thread: 2 Guest(s)

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.