Posts: 5,653
Threads: 0
Joined: May 2005
Location: Centre County Pennsylvania
I found the wrenches for my tablesaw arbor behind my bandsaw on the floor under a pile of wood. Not much good there, and I was about to change the blade for a plywood blade. It's fortunate I'm cleaning.
Should I just drill a hole in the front of the saw cabinet and install a hook for them? What have you done to keep them where you can find them?
Posts: 1,150
Threads: 0
Joined: Nov 2006
Location: Texas - Gods Country
(05-27-2018, 08:09 AM)EricU Wrote: I found the wrenches for my tablesaw arbor behind my bandsaw on the floor under a pile of wood. Not much good there, and I was about to change the blade for a plywood blade. It's fortunate I'm cleaning.
Should I just drill a hole in the front of the saw cabinet and install a hook for them? What have you done to keep them where you can find them?
magnets maybe?
my saw has a hook to hang them on though on the cabinet.
Posts: 24,145
Threads: 2
Joined: Sep 2003
Location: Missouri
05-27-2018, 10:28 AM
(This post was last modified: 05-27-2018, 11:30 AM by Stwood_.)
All my round blades and wrenches are in 2 special made drawers under my miter saw cabinet.
Steve
Mo.
I miss the days of using my dinghy with a girlfriend too. Zack Butler-4/18/24
The Revos apparently are designed to clamp railroad ties and pull together horrifically prepared joints
WaterlooMark 02/9/2020
Posts: 12,605
Threads: 0
Joined: Aug 2003
Location: Wapakoneta, OH
I use to just use some rare earth magnets and stick them to the front of the cabinet. Sine then I've added a cabinet under the extension, it has a drawer for the wrenches and other stuff like dado insert, etc.
I started with absolutely nothing. Now, thanks to years of hard work, careful planning, and perseverance, I find I still have most of it left.
Posts: 18,492
Threads: 0
Joined: Jul 2006
Location: Milwaukee area
Overhead on a joist (if available) can also be handy.
Posts: 3,545
Threads: 1
Joined: May 2004
Location: Wisconsin
Attached to the cord near the plug.
Posts: 82
Threads: 0
Joined: Sep 2016
Location: NE Iowa
Dado blade insert, blade wrenches, allen wrenches for motor cover/back plate, spare riving knife are all on a magnetic tool holder on the front of the saw.
Posts: 5,653
Threads: 0
Joined: May 2005
Location: Centre County Pennsylvania
(05-28-2018, 07:18 AM)Lucky Irish Wrote: Dado blade insert, blade wrenches, allen wrenches for motor cover/back plate, spare riving knife are all on a magnetic tool holder on the front of the saw.
that's a good idea. I was hoping one of the hard drive magnets I have sitting around would work, but they aren't very strong from the backside.
Posts: 1,998
Threads: 1
Joined: Aug 2016
(05-28-2018, 07:25 AM)EricU Wrote: that's a good idea. I was hoping one of the hard drive magnets I have sitting around would work, but they aren't very strong from the backside.
There are spare mounting holes on backside of the square tube for the rip fence. I installed a long bolt with about 3" extending out the back with a double nut. Hang the wrenches and table inserts on that. Not in the way of the fence sliding. Roly
Posts: 4,751
Threads: 0
Joined: Aug 2006
[attachment=10653][attachment=10653]A few years ago I sent my method of storing ts wrenches to a wood rag, and won $100 for the tip!
Wrenches are next to the plug, so you have no excuse to not unplug, when changing blades.
I long for the days when Coke was a soft drink, and Black and Decker was a quality tool.
Happiness is a snipe free planer
