Posts: 4,004
Threads: 0
Joined: Nov 2010
Ok, layout work...
 ...got out two pieces of scrap Pine, that matched the thicknesses of the frame and kicker, combined....Marked out a "Top" on the panel. Set the pair a little below the top edge....wanted room for the corner glue blocks to sit. Large square to mark the layout lines across the panel......allowing a 7" space for each drawer ( using 1 x 8s for the drawers) measuring from bottom of the kicker to the top of the next frame...
Got to the "bottom" and measured down from the top of the frame 5"..to form the feet....used an old varnish can to mark a profile
Hmmm, seems the can had a dent....will fine tune that away, before I trace onto the other panel
Had two "Vintage" Sabresaws ( B&D made)...chose one for the straight cuts on the feet..
Yep, an all metal sabre saw. cut was quiet, no deflections...ran great ( new blade helps
)..the green plastic bodied one got a scrolling blade, to do the curves
Yep, bad curve...will clean that up after awhile....Got out a "speed square"
Have a job for this to do. Involves cutting sockets for sliding dovetails....stay tuned...
Show me a picture, I'll build a project from that
Posts: 4,004
Threads: 0
Joined: Nov 2010
07-04-2018, 10:15 AM
(This post was last modified: 07-04-2018, 10:18 AM by bandit571.)
To set the speed square, first I needed to know how far from the center of the router bit to the edge of the router base was
I also needed to mark the center of the socket....and then set the speed square for that distance..
Used a larger square, to set things square to the edge. 2 clamps to hold the jig, the panel and the bench together,,,didn't want any to move around
Speed square does have a cleat, 90 degrees to the long side, underneath....jig is at least 10 years old, so it is nice to double check it...Router was fired up, pushed through the cut, while also pushing the router against the fence...didn't want it wandering around....then pull the router back through the cut to clean it out...
Then, reset the speed square for the next cut...slide the panel down to where I can clamp it up. And then make the second socket out of four needed..
Was getting a bit worn out ( me, that is
) so I cleaned up the shop, and then called it a day.....I did rotate the panel around, so I can do the other two slots.....
Maybe today, I can go and hide out in the shop?
maybe get the side all groovy? Both side panels will need a rebate along the back edge...to house the plywood back.
Stay tuned...
Show me a picture, I'll build a project from that
Posts: 5,182
Threads: 0
Joined: Jan 2014
Location: Santa Maria, Ca
Rock on Bandit!!
We love these builds that you so kindly post.
Mark Singleton
Bene vivendo est optimum vindictae
The Laws of Physics do not care about your Politics - Me
Posts: 4,004
Threads: 0
Joined: Nov 2010
Well..got the other two sockets done on Side #1, today..
The worked on a rebate along the edge, for the plywood back.
Used the #78...which is why my left thumb is sore...
Set side #1 aside, and planed side #2 flat.....then set #1 on top..
And marked where the cuts would be. I also marked where the dovetail sockets will be..
Then got things ready to do some cutting....stay tuned
Show me a picture, I'll build a project from that
Posts: 4,004
Threads: 0
Joined: Nov 2010
Feet profile was cut with the vintage sabresaw..
When I have both sides clamped together, a beltsander can match them up. Other (top, this time) end needed a straight crosscut..speedsquare guided, of course
Used the all metal SKIL saw, 6" blade style..
Then used the speed square and the router, to cut the dovetail sockets. Then that thumb-bruiser #78 to mill a rebate on side#2...finally, with the legs getting crampy...just clamped the two sides together...
Mainly to check how the sockets line up....Decided to just leave the sides where they were..
And clean the mess up off the floor...again...Shop's trash can is already 1/4 full....
Legs hurt, thumb's sore..time to stop for the day.....almost got something done, today
Stay tuned...
Show me a picture, I'll build a project from that
Posts: 4,004
Threads: 0
Joined: Nov 2010
Running out of time....
Got a dry fit done..
Going to take a LOT of clamps....
Sides are a bit bowed in the middle....good thing I bought a few extra pipe clamps in the yard sales
May try a glue-up...IF I can get motivated out of the chair....60 degrees outside...may need a coat?
A dab of glue as each frame is slid into place. Maybe I can get the panel for the top cut to length. Then find a use for the cut-offs
Need to add the kickers to the frames, then do the glue up.....Case will then have to sit around for awhile...until I am cleared to go back into the shop....then maybe do the face frame, and then three drawers built? Through dovetails for the drawer fronts, dado to connect the back....Stanley #45 to make a groove for the drawer bottoms?
Show me a picture, I'll build a project from that
Posts: 21,259
Threads: 2
Joined: Mar 2009
Location: IA
Goodness
You could make a house hold full of furniture in just a few months by yourself.
Nice work again!!!
As of this time I am not teaching vets to turn. Also please do not send any items to me without prior notification. Thank You Everyone.
It is always the right time, to do the right thing.
Posts: 4,004
Threads: 0
Joined: Nov 2010
Got the kickers made..
Top has been cut to size, corners are rounded...
Kickers have been installed, sides attached to the frames..
And the corner blocks were made and installed...
Even had a couple pipe clamps left over...
Turned the assembly around so I could stash it here....out of the way, for a day or two....until the next batch of lumber arrives..
Stay tuned
Show me a picture, I'll build a project from that
Posts: 4,004
Threads: 0
Joined: Nov 2010
Well, clamps have been removed, and stashed
Holes drilled..
Leaned the drill, back and forth, to make a slot
Centered the case onto the top, after I figured out which face was the better of the two
and added a screw into each slot. Didn't have the exact length, and a 2" was too long...grinder to shorten a bit, and add a new point..
Unless I need the bench anytime soon..I'll leave the case here...
Now just waiting on the rest of the lumber to arrive. Maybe by the weekend
Stay tuned..
Show me a picture, I'll build a project from that
Posts: 21,259
Threads: 2
Joined: Mar 2009
Location: IA
Bandit
Is that center rail a guide for the drawers? If so do you put a grove in the drawer or boards to guide the drawer?
As of this time I am not teaching vets to turn. Also please do not send any items to me without prior notification. Thank You Everyone.
It is always the right time, to do the right thing.
|
