Posts: 1,868
Threads: 0
Joined: Dec 2002
so i'm making something like this...
wood-toy-chest-wood-storage-toy-shelf-toy-storage-wood-toy-bin-storage-solution-farmhouse-toy-bin-farmhouse-storage-wood-furniture
haven't really done woodworking in over a decade so i'm questioning how i'm going to get this done. to attach the bottom and the back, would you guys use pocket holes and glue or brad nails and glue? i'm using red oak 3/4" ply.
also, the pocket hole screws i have are 1.25" pan head - are these hard to plug?
thanks for any info!
Posts: 596
Threads: 0
Joined: Mar 2007
Location: NW of Fort Worth, TX
Is the back and bottom 3/4" stock as well? If so for the bottom and the back I would lean toward the screws rather than the brads, but I probably would not plug either one, just drill from the non-show side.
Posts: 1,868
Threads: 0
Joined: Dec 2002
yes, the back and bottom are 3/4" ply.
Posts: 5,653
Threads: 0
Joined: May 2005
Location: Centre County Pennsylvania
brads are mostly useful for holding the pieces in place while gluing. Even then you need clamps.
Posts: 194
Threads: 1
Joined: Jul 2016
Location: WI
Given those choices, I would use pocket holes and glue.
Posts: 13,412
Threads: 4
Joined: Jun 2007
Location: New Jersey
Personally, I'd rabbet the inside edges of the sides, fit the back and bottom into the rabbet, glue and brad, or use a regular screws.
Credo Elvem ipsum etiam vivere
Non impediti ratione cogitationis
Posts: 7,421
Threads: 1
Joined: Sep 2005
Dowels. Most of the cabinet makers use dowels. They are stronger for sheet goods. A self centering jig + dowel centers makes this easy.
Dowels position the boards easily and hold the boards in position better than even tight dadoes.
No animals were injured or killed in the production of this post.
Posts: 741
Threads: 0
Joined: Mar 2006
07-18-2018, 10:29 AM
(This post was last modified: 07-18-2018, 10:30 AM by jasfrank.)
I'd do as Rich says, fit the panels in rabbets and glue. But I always use staples instead of brads or screews. Much faster, and better holding power. If things are fitted correctly no clamps really needed. Thats assuming you are dealing with a non-showing side.
Posts: 14,929
Threads: 0
Joined: Sep 2004
Location: Butler, PA
(07-18-2018, 08:41 AM)Admiral Wrote: Personally, I'd rabbet the inside edges of the sides, fit the back and bottom into the rabbet, glue and brad, or use a regular screws.
This is the more elegant solution and from a woodworking practices perspective, probably the preferred method. However, the pocket holes would work fine.
You can avoid plugging the holes by putting in a no-show location, as was suggested. Kreg does sell special wood plugs that fit the hole. They are available in different wood species to "match" what you are building, but they don't match very well. You essentially end up with a plug that is sort of end grain, sliced on an angle, that you are inserting into face grain. They aren't going to grain match very well, but they do fill the void of the hole well enough.
If you are going down a river at 2 mph and your canoe loses a wheel, how much pancake mix would you need to shingle your roof?
Posts: 304
Threads: 0
Joined: Jul 2007
07-18-2018, 11:09 AM
(This post was last modified: 07-18-2018, 11:10 AM by rudedan60.)
Kreg, now makes a jig for making your own plugs. The advantage, I see is matching the material. It is a bit pricey though. Dan
