08-24-2018, 11:47 AM
(08-24-2018, 10:58 AM)Stwood_ Wrote: Ah I see now. Guess they were copying tools back then too.
i think so
Formerly known as John's Woodshop
|
Daily Bench Shot
|
 i think so
08-24-2018, 01:22 PM
(This post was last modified: 08-24-2018, 01:23 PM by Belle City Woodworking.)
With some help I flipped the tabletop and got to work on the bottom of the table. I also found the straightest board in the pile of salvaged lumber for the breadboard ends and I got those roughed out. I will get to work on the mortise and tenons and will secure them with draw bores.
![[Image: XMRY4dc2_Qzy_Az_Dw8o_Lg.jpg]](https://s26.postimg.cc/4p3lqa3o9/XMRY4dc2_Qzy_Az_Dw8o_Lg.jpg) I am convinced that this is about the biggest project I would be able to do in my basement shop 
Formerly known as John's Woodshop
08-24-2018, 02:02 PM
Time to stop and fix some air guns. One 16ga., two 18ga., and a 1/4" crown stapler.
Stapler I just cleaned up and greased the o-rings. 
The 16ga needed a driver bumper and a seal. $31.00 for those 2 pieces of plastic laying by the hex T wrench. 
Steve
Mo. I miss the days of using my dinghy with a girlfriend too. Zack Butler-4/18/24 The Revos apparently are designed to clamp railroad ties and pull together horrifically prepared joints WaterlooMark 02/9/2020 
09-05-2018, 09:55 PM
Had to put a diaghpram kit in the carb for my brushcutter.......made it 21 years.
Ed 
09-09-2018, 01:00 PM
Mine is currently covered with the last of my machine tooling.... It is being sold and going out the door so I can get back to some relaxation and peaceful woodworking!! It is good to be back!
![[Image: S1DmxJMl.jpg]](https://i.imgur.com/S1DmxJMl.jpg)
I am quickly realizing that I have NO natural talent... But I am trying to fake it.
09-09-2018, 08:07 PM
Spent the day fixing the rest of my nail guns that had quit, or needed attention.
$60.00 in parts and five more are back in service. These are all the older series guns that I feel are better than PC's current lineup of air guns, so I'm keeping them around.
I also got my BBQ spatula re-riveted.  Fuzzy picture. I need a new camera. 
Steve
Mo. I miss the days of using my dinghy with a girlfriend too. Zack Butler-4/18/24 The Revos apparently are designed to clamp railroad ties and pull together horrifically prepared joints WaterlooMark 02/9/2020
09-09-2018, 10:42 PM
Got our "team Bancroft" sawmill running today, been 4 years since I used it. Need to clean the crap out of the mill shed yet.
My first load of way overdoo to mill logs is on the trailer. 3 white oak & 5 cherry, going to be lots of lost lumber from setting, it is what it is. Nobody's fault but mine. Ed
Paint the ends.................
 Nice trailer...........
Steve
Mo. I miss the days of using my dinghy with a girlfriend too. Zack Butler-4/18/24 The Revos apparently are designed to clamp railroad ties and pull together horrifically prepared joints WaterlooMark 02/9/2020 (09-09-2018, 11:31 PM)Stwood_ Wrote: Paint the ends................. Paint isn't going to do anything when the logs sit for 4 years.  This load should be decent on the yield, the red oak won't be pretty, already lost the soft maple & walnut. The trailer is the deckover from he11, 18' lg and 4k lbs. The frame is 12" I-beam, slightly overkill. Ed
09-09-2018, 11:44 PM
(09-09-2018, 11:37 PM)EdL Wrote: The frame is 12" I-beam, slightly overkill. Uuummm yea. Bet it rides good though. No bounce....
Steve
Mo. I miss the days of using my dinghy with a girlfriend too. Zack Butler-4/18/24 The Revos apparently are designed to clamp railroad ties and pull together horrifically prepared joints WaterlooMark 02/9/2020 |
|
|
Users browsing this thread: 34 Guest(s)