Posts: 2,726
Threads: 0
Joined: Dec 2005
Posts: 30,415
Threads: 1
Joined: Dec 2002
Location: DuPage County, Illinois, USA
10-30-2018, 11:53 PM
(This post was last modified: 10-30-2018, 11:55 PM by Cian.)
I hang out in a Machnists forum for curiosity and interest. After seeing the number of operations required to make a precision hand tool, I am now surprised how seemingly "cheap" some top tier tools may be. Case in point.
Also, I have the single rod version of this marking gauge, and as always, it's made with excellent craftsmanship.
Posts: 2,726
Threads: 0
Joined: Dec 2005
Yes, the 35th anniversary model is a winner for sure: always on my bench (and shows no propensity to roll off the bench!)
(10-30-2018, 11:53 PM)Cian Wrote: I hang out in a Machnists forum for curiosity and interest. After seeing the number of operations required to make a precision hand tool, I am now surprised how seemingly "cheap" some top tier tools may be. Case in point.
Also, I have the single rod version of this marking gauge, and as always, it's made with excellent craftsmanship.
Posts: 162
Threads: 0
Joined: Jun 2005
(10-31-2018, 07:00 AM)Philip1231 Wrote: Yes, the 35th anniversary model is a winner for sure: always on my bench (and shows no propensity to roll off the bench!)
Thanks for the 'heads up'....got mine today with free shipping!!
Posts: 18,494
Threads: 0
Joined: Jul 2006
Location: Milwaukee area
(10-30-2018, 11:53 PM)Cian Wrote: I hang out in a Machnists forum for curiosity and interest. After seeing the number of operations required to make a precision hand tool, I am now surprised how seemingly "cheap" some top tier tools may be. Case in point.
Also, I have the single rod version of this marking gauge, and as always, it's made with excellent craftsmanship.
Isn't that the truth!
If I had to make/sell/support them, I'd want a minimum of several hundred bucks, and there would be a special application process to get in line to buy one.
Posts: 5,653
Threads: 0
Joined: May 2005
Location: Centre County Pennsylvania
If I had to make a 1/2-20 hex head bolt it would cost you a couple hundred $. But I'm pretty sure I could match the price of this marking gauge with short production run quantities. I'd have to send it out, of course.
Posts: 18,023
Threads: 0
Joined: Aug 2002
For those that pick one up, let us know how well it stays locked in use. I have their pocket dual marking gauge that is also stainless steel. I have problems with the gauge losing its settings and the head slipping in use. I think it’s more of an issue with the small locking knob rather than the stainless steel rods. Be interesting to see if this one has a similar issue.
I can’t justify a purchase of one since I already have a vintage Goodell-Prat with dual marked shafts and a large octagonal head. I think it was a basis of some of the design choices Lee Valley used in their marking gauge.
John
Posts: 2,382
Threads: 0
Joined: Dec 2011
My dual gauge does not slip. I used to have two of it.
Contact Lee Valley to exchange yours with a good one.
Simon
Posts: 136
Threads: 0
Joined: Sep 2006
I appreciate the little rubberized washer on the end of one of the SS rods to prevent the yoke that holds the rod setting from sliding off.
I cannot budge the rods once they are set and yet they slide easily if unlocked.
![[Image: 05N7040s1.jpg]](http://www.leevalley.com/en/images/item/Woodworking/MarkMeasure/05N7040s1.jpg)
