Posts: 31
Threads: 0
Joined: Mar 2016
I'm building an Arts and Crafts blanket chest. The construction is groove and tenon for the carcass. Seems to me that I could get a much better finishing job if I were to finish the parts before glue up because I can get the finishi into places that would be hard to reach after gluing up (corners, etc.). This of course means I'll have to avoid getting finish on the surfaces to be glued.
For the finish, I plan to use Watco with three coats of wipe-on poly.
Is there a compelling reason NOT to finish before glue up?
Just curious. Thanks in advance!
- Ray
Posts: 86
Threads: 0
Joined: Jul 2016
no reason not to finish before the gluing - i usually finish the insides and blue tape the glue joints for the glue-up
jerry
Posts: 12,299
Threads: 0
Joined: Mar 2006
I've gotten into the habit of finishing some parts before glue-up. For those that need assembled prior to finishing, I also use painter's tape.
Posts: 2,488
Threads: 0
Joined: Aug 2004
(10-23-2020, 10:20 AM)Tony Z Wrote: I've gotten into the habit of finishing some parts before glue-up. For those that need assembled prior to finishing, I also use painter's tape.
+1
Jim
Posts: 1,618
Threads: 0
Joined: Feb 2010
Location: Coast of Maine
(10-23-2020, 10:52 AM)Halfathumb Wrote: +1
+2
I've only had one...in dog beers.
"You can see the stars and still not see the light"
The Eagles: Already Gone
Posts: 2,274
Threads: 90
Joined: Jun 2001
(10-23-2020, 03:27 PM)shoottmx Wrote: +2
+3
John
Always use the right tool for the job.
We need to clean house.
Posts: 31
Threads: 0
Joined: Mar 2016
(10-23-2020, 04:52 PM)John Mihich Wrote: +3
Thank you all!
Posts: 2,384
Threads: 0
Joined: Dec 2011
10-25-2020, 09:53 AM
(This post was last modified: 10-25-2020, 09:56 AM by Handplanesandmore.)
Not in your case, but there're good reasons why finish should be done after gluing up -
Hand-cut dovetail joints if the pins are proud. You need to glue it up, flush the surfaces before finishing
In some cases, clamping could leave marks on a finish or if not careful, indention on softwood which needs to be fixed (with heat).
I choose the method depending on what I'm making, how hard the assembly is, size, etc.
As for the blanket case, either way would work for me because it's relatively large and it won't be difficult to reach inside.
Simon
Posts: 272
Threads: 0
Joined: Jan 2007
Location: Warrenton, MO
I understand your point but I think finishing before glue-up is fraught with unexpected problems. How many time do you have to tap on the joint to get it to mate properly? Will you mar your brand new, probably still somewhat soft finish? And so on. I do often stain before glue-up just because getting everything properly covered isn't always easy. If there is any movement to the joint you can easily show unstained wood. Full disclosure I dye more than stain so there is no oil residue in the joints when I do this.
Was living the good retired life on the Lake. Now just living retired.
Posts: 16,471
Threads: 0
Joined: Mar 2005
(10-23-2020, 09:33 AM)RayFleck Wrote: I'm building an Arts and Crafts blanket chest. The construction is groove and tenon for the carcass. Seems to me that I could get a much better finishing job if I were to finish the parts before glue up because I can get the finishi into places that would be hard to reach after gluing up (corners, etc.). This of course means I'll have to avoid getting finish on the surfaces to be glued.
For the finish, I plan to use Watco with three coats of wipe-on poly.
Is there a compelling reason NOT to finish before glue up?
Just curious. Thanks in advance!
- Ray
The Wood Whisperer discusses the topic:
https://thewoodwhisperer.com/videos/ente...nter-pt-4/
--
See ya later,
Bill
