Posts: 167
Threads: 0
Joined: May 2013
Location: NW Iowa
Hi There. I just picked up some exotic wood blanks from a garage sale. They are all labelled as Rockler and they are covered with a waxy substance, which I presume is meant to protect from oxidation. Before I start in with a card scraper to remove the wax, does anybody have a faster way?
Posts: 2,213
Threads: 1
Joined: Sep 2003
Location: Maryland
Not that I have an answer to your question....but Rockler blanks come waxed to keep the moisture in and prevent checking until the piece is turned.
Posts: 6,179
Threads: 0
Joined: Dec 2002
Location: Bothell, WA
Running them through the jointer is faster.
Cellulose runs through my veins!
Posts: 12,053
Threads: 1,611
Joined: Jan 2001
Location: Kansas City, Kansas
Posts: 314
Threads: 0
Joined: Feb 2012
Location: Carson Valley, NV
(10-29-2020, 11:50 AM)joe1086 Wrote: Not that I have an answer to your question....but Rockler blanks come waxed to keep the moisture in and prevent checking until the piece is turned.
And to add... When you clean the wax off you better be ready to turn, because in most cases they will begin to check pretty quickly once the wax "seal" is removed. Don't ask me how I know
Posts: 24,145
Threads: 2
Joined: Sep 2003
Location: Missouri
I can understand using a jointer, but I don't think I would want all that wax in my planers steel rollers, if it would even grab enough to pull it through.
Steve
Mo.
I miss the days of using my dinghy with a girlfriend too. Zack Butler-4/18/24
The Revos apparently are designed to clamp railroad ties and pull together horrifically prepared joints
WaterlooMark 02/9/2020
Posts: 14,865
Threads: 10
Joined: Jan 2010
Location: southeastern VA
(10-29-2020, 03:57 PM)SteveS Wrote: Turning them on the lathe is faster.
fixt
What sort of blanks are we talking?
If pen blanks, drill and lightly use a countersink on the end that you are inserting the tube (just to keep from smearing the wax into the glue-up. Center the tube length-ways and the trimmer will cut the wax right off.
Bowl blanks would depend on what you use to hold the blank for roughing. Unless you can verify that the blank has dried out in the wax, I would treat it like a green turning and do a twice-turn approach. Of course, if you are into thin bowls that are not round, never mind.
Peppermills might be problematic if the wood is still wet. If you have a way to check for moisture content, then you can tell if the blank(s) is(are) ready to become a mill or if it needs a few more years in wax.
"the most important safety feature on any tool is the one between your ears." - Ken Vick
A wish for you all: May you keep buying green bananas.
Posts: 167
Threads: 0
Joined: May 2013
Location: NW Iowa
The blanks that I purchased at the garage sale were all different shapes and sizes. The gal at the sale said that they were all 20 yr + old.
Posts: 313
Threads: 5
Joined: Jul 2016
Just my preference, but I've always used a scraper and kept it away from the machines. Probably unfounded, but if there's anything in the coating that I don't want on my blades, push pads or anything else, I don't want to take the risk that it transfers to something else (recognizing it should just be wax, which is why this is probably unfounded). As a hobbyist so I'm not worried about the extra few minutes it takes, and I've never found it to take very long even on large bowl blanks. To the extent there are inclusions with wax in them, those just get turned away.
Posts: 46,966
Threads: 0
Joined: Nov 2002
Location: east coaster
(10-30-2020, 09:44 AM)jcredding Wrote: Just my preference, but I've always used a scraper and kept it away from the machines. Probably unfounded, but if there's anything in the coating that I don't want on my blades, push pads or anything else, I don't want to take the risk that it transfers to something else (recognizing it should just be wax, which is why this is probably unfounded). As a hobbyist so I'm not worried about the extra few minutes it takes, and I've never found it to take very long even on large bowl blanks. To the extent there are inclusions with wax in them, those just get turned away.
that's what i do too . . . scrape off the worst of it.
