Posts: 4,023
Threads: 0
Joined: Nov 2010
04-02-2021, 12:38 PM
A $4 mystery....picked back on last Friday...from the sides, it looks just like a "normal" mortise or sash chisel 1/8" wide...
Bevel looked a bit rounded, is all....Brass furniture...octagonal bolster.....1/8" was a size I "needed"...however...
I doubt if I will flatten the back......may flatten the curved bevel?
So, who would put a groove along the back of such a skinny chisel? And....how to sharpen something like this?
Show me a picture, I'll build a project from that
Posts: 217
Threads: 0
Joined: Dec 2003
Location: Arizona Desert
(04-02-2021, 12:38 PM)bandit571 Wrote: A $4 mystery....picked back on last Friday...from the sides, it looks just like a "normal" mortise or sash chisel 1/8" wide...
Bevel looked a bit rounded, is all....Brass furniture...octagonal bolster.....1/8" was a size I "needed"...however...
I doubt if I will flatten the back......may flatten the curved bevel?
So, who would put a groove along the back of such a skinny chisel? And....how to sharpen something like this?
Could be a carving chisel or bead turning lathe tool.
Posts: 428
Threads: 0
Joined: Apr 2006
(04-02-2021, 12:38 PM)bandit571 Wrote: A $4 mystery....picked back on last Friday...from the sides, it looks just like a "normal" mortise or sash chisel 1/8" wide...
Bevel looked a bit rounded, is all....Brass furniture...octagonal bolster.....1/8" was a size I "needed"...however...
I doubt if I will flatten the back......may flatten the curved bevel?
So, who would put a groove along the back of such a skinny chisel? And....how to sharpen something like this?
Carving gouge I believe.
Posts: 14,860
Threads: 10
Joined: Jan 2010
Location: southeastern VA
04-03-2021, 09:58 PM
(This post was last modified: 04-03-2021, 09:59 PM by iclark.)
(04-02-2021, 01:34 PM)dry heat Wrote: Could be a carving chisel or bead turning lathe tool.
I have a parting tool for the lathe that has a groove like that. It is one of my favorites.
I suspect that that one could be useful for vining or inlay.
"the most important safety feature on any tool is the one between your ears." - Ken Vick
A wish for you all: May you keep buying green bananas.
Posts: 10,722
Threads: 1
Joined: Jan 2006
Location: Orlando, Florida
I don't think it's a lathe tool since it appears there's not much of a tang. I'm in the carving tool camp.
Still Learning,
Allan Hill
Posts: 116,204
Threads: 0
Joined: Jun 2002
Location: Sparkling Clearwater, Fl. Tampa Bay Area
(04-05-2021, 06:51 AM)AHill Wrote: I don't think it's a lathe tool since it appears there's not much of a tang. I'm in the carving tool camp.
.................
Not a lathe tool...it's a sash gouge.
Often Tested. Always Faithful. Brothers Forever
Jack Edgar, Sgt. U.S. Marines, Korea, America's Forgotten War
Get off my lawn !
Posts: 1,153
Threads: 1
Joined: Jun 2010
Location: South Central PA
Looks to be a carving veiner. Is that a number on the top?
Posts: 4,023
Threads: 0
Joined: Nov 2010
No number found....
Show me a picture, I'll build a project from that
Posts: 2
Threads: 0
Joined: Apr 2021
Looks like a purfling cutter that has been (badly) re-handled. The suggestion about a veiner I don’t go with, as a gouge would not need or have the depth. A parting tool is possible, with a user made handle - the two turned hollows are a clue.
Sharpening - depends on use. - either suggestion only needs you to establish a single bevel, and the groove will ensure that you have a v shape with ‘sharp’ edges.
This is not a tool for hogging off material, and the combination of a 90 degree arris and the angle of the tool to the work will do the job. What angle to set the bevel depends on which job you are asking it to do.
.
