Posts: 481
Threads: 0
Joined: May 2003
Location: Rhode Island
I have 50 - 2x6 tongue and groove pine cut-offs, an average length of 25”, that I would like to slice in half. Not sure what the best bet in a blade would be. I have a 17” Grizzly that I bought used a few years ago. There is a 1/2” blade that came with the saw but it seems too fine, I believe it’s 6 TPI. It whines when I tried to make a cut and was taking way too much effort than I thought should be required. Looking for advice on what type of blade and mfg. Thanks
Posts: 12,876
Threads: 0
Joined: Jan 2010
Location: Lewiston, NY
(11-22-2022, 05:24 PM)digger Wrote: I have 50 - 2x6 tongue and groove pine cut-offs, an average length of 25”, that I would like to slice in half. Not sure what the best bet in a blade would be. I have a 17” Grizzly that I bought used a few years ago. There is a 1/2” blade that came with the saw but it seems too fine, I believe it’s 6 TPI. It whines when I tried to make a cut and was taking way too much effort than I thought should be required. Looking for advice on what type of blade and mfg. Thanks
Try a 3 tpi blade. Your choice if you prefer a 1/2" or 3/4" wide one. Either will do the job.
John
Posts: 2,331
Threads: 0
Joined: Dec 2006
Location: virginia beach VA
+1 with John. Though if the current blade is the one that came with the saw, I would toss it. The blade that came with my Grizzly was totatlly useless.
Posts: 2,827
Threads: 2
Joined: Nov 2003
Location: S.E. Michigan
11-23-2022, 10:11 AM
Get a 3 tpi 3/4" blade and you will be in good shape.
Posts: 1,612
Threads: 0
Joined: Oct 2008
(11-23-2022, 10:11 AM)med-one Wrote: Get a 3 tpi 3/4" blade and you will be in good shape.
+1
Crank that tension knob as tight as you can and watch your fingers.
Posts: 481
Threads: 0
Joined: May 2003
Location: Rhode Island
Thanks for the info......
Posts: 12,876
Threads: 0
Joined: Jan 2010
Location: Lewiston, NY
(11-23-2022, 12:34 PM)DieselDennis Wrote: +1
Crank that tension knob as tight as you can and watch your fingers.
Better to make a tension gage and know how much tension you are applying. No sense over stressing the blade or saw. And if you find out the saw can't apply enough tension to a 3/4" blade you'll know to buy a 1/2" one. What's enough tension? 20 - 25 ksi is a good number to shoot for. But don't try that with a 14" cast iron saw except on 1/4" or narrower blades because they are not capable of doing it on 1/2" blade, much less one that's 3/4". About all you can comfortably apply to a 1/2" blade on a 14" cast iron saw is 12 ksi. Anything higher and the frame deflects so much that the upper blade guide goes seriously out of alignment.
Let the data drive how you tension your saw.
John
Posts: 14,849
Threads: 10
Joined: Jan 2010
Location: southeastern VA
FWIW, I have heard of people who got really good deals on BS's because the blades were installed upside down. It is much easier to do than one might think (if you do not know that it is a possibility).
If this is the blade that came on the BS when you got it used (and you have never changed it), it could be worth taking a close look to make sure that the teeth are pointing in the right direction.
With the teeth pointing up, the saw will still cut, but it takes more effort than it should, it is slow, and there is extra noise.
"the most important safety feature on any tool is the one between your ears." - Ken Vick
A wish for you all: May you keep buying green bananas.
Posts: 2,827
Threads: 2
Joined: Nov 2003
Location: S.E. Michigan
Clark,
It's funny you should say this, but I bought a Jet long bed jointer for 150.00 and the guy said he was getting a bigger one. Upon closer examination, he had the blades in backward.
Posts: 12,876
Threads: 0
Joined: Jan 2010
Location: Lewiston, NY
(11-27-2022, 09:04 AM)med-one Wrote: Clark,
It's funny you should say this, but I bought a Jet long bed jointer for 150.00 and the guy said he was getting a bigger one. Upon closer examination, he had the blades in backward.
I hope it was one with an insert head.
John
