Posts: 2,608
Threads: 0
Joined: Feb 2001
I have some 6” flex hose that is a very tight fit on the inlet of the super dust deputy.
In the past, I’ve struggled to get the flex hose stretched enough to get it on the SDD.
so today I used a 6” hole saw and cut a disk out of 2x material then cut a 2” hole out of the middle of that. Then I cut the wood donut into 4 quarters.
A little painters tape to hold it back together and it fits right into the end of the 6” flex hose.
An exhaust tubing expansion tool slipped into the middle of the wood donut and run the expansion tool until it breaks the tape and stretched the hose.
The hose easily goes onto the fitting then it’s memory makes it a tight fit. I’m still using a clamp but with such a tight fit I’m not sure it’s necessary.
Hope someone else finds this useful.
Duke
Posts: 21,984
Threads: 0
Joined: Oct 2003
If you cut a 6”’ disc then removed 2” from the center and quartered it, you still have 4”—that’s a lot to stretch the hose.
???
Gary
Please don’t quote the trolls.
Liberty, Freedom and Individual Responsibility
Say what you'll do and do what you say.
Posts: 13,416
Threads: 4
Joined: Jun 2007
Location: New Jersey
(08-23-2023, 03:40 PM)Gary G™ Wrote: If you cut a 6”’ disc then removed 2” from the center and quartered it, you still have 4”—that’s a lot to stretch the hose.
???
He cut a hole in the center of the 6" disc, then quartered it.
Credo Elvem ipsum etiam vivere
Non impediti ratione cogitationis
Posts: 13,416
Threads: 4
Joined: Jun 2007
Location: New Jersey
(08-23-2023, 11:01 AM)JDuke Wrote: I have some 6” flex hose that is a very tight fit on the inlet of the super dust deputy.
In the past, I’ve struggled to get the flex hose stretched enough to get it on the SDD.
so today I used a 6” hole saw and cut a disk out of 2x material then cut a 2” hole out of the middle of that. Then I cut the wood donut into 4 quarters.
A little painters tape to hold it back together and it fits right into the end of the 6” flex hose.
An exhaust tubing expansion tool slipped into the middle of the wood donut and run the expansion tool until it breaks the tape and stretched the hose.
The hose easily goes onto the fitting then it’s memory makes it a tight fit. I’m still using a clamp but with such a tight fit I’m not sure it’s necessary.
Hope someone else finds this useful.
Duke
I had the same problem with a hose on a Billy Goat debris loader output tube; used a heat gun to soften the end and expand it just enough. Worked for me. But I appreciate your mechanical solution.
Credo Elvem ipsum etiam vivere
Non impediti ratione cogitationis
Posts: 2,608
Threads: 0
Joined: Feb 2001
(08-23-2023, 05:00 PM)Admiral Wrote: I had the same problem with a hose on a Billy Goat debris loader output tube; used a heat gun to soften the end and expand it just enough. Worked for me. But I appreciate your mechanical solution.
I tried that with the 6” hose, but couldn’t get enough of it warm enough to go around the fitting.
Posts: 24,145
Threads: 2
Joined: Sep 2003
Location: Missouri
Great solution. I'll hafta remember that. I've always just lubed the inside of the hose with a dab of white grease
Steve
Mo.
I miss the days of using my dinghy with a girlfriend too. Zack Butler-4/18/24
The Revos apparently are designed to clamp railroad ties and pull together horrifically prepared joints
WaterlooMark 02/9/2020
Posts: 1,687
Threads: 0
Joined: Apr 2005
That's a very clever solution. Did you have the pipe stretcher? Rent one from an auto parts store?
Posts: 2,608
Threads: 0
Joined: Feb 2001
I had the stretcher but at $20-30 from harbor freight it’s worth getting one.
Posts: 1,809
Threads: 0
Joined: Nov 2006
Location: SF Bay Area
It is frustrating how DC fittings don't seem designed to fit well together.
Warming up the end of the hose in a bowl of hot water has been enough for me to get it over the SDD ports.
