Posts: 2,574
Threads: 0
Joined: Feb 2001
I found a forstner bit on amazon that was listed as 3/5” but it’s actually a 15mm bit.
3/5 or 0.6 inches is closer to 15.24mm
Why you may ask do I want a 3/5 inch forstner bit.
I am making a copy of the base of a bentwood case for a singer sewing machine, and the hinges that they used were 0.6 inch or 3/5
And need couple holes in the back of the case that are right around 0.6 inch.
15mm is to small and 16mm is too big.
I did try to grind a 16mm steel bit down to 15.24 and it was enough that it took most of the teeth off the forstner bit.
I also have ordered a 16mm carbide bit, and am going to try grinding the carbide down a little bit to get to the 15.24 or 15.25mm diameter.
Anyone have any other suggestions on how to get a good flat bottomed hole other than the above?
Thanks in advance.
Duke
Posts: 12,601
Threads: 0
Joined: Aug 2003
Location: Wapakoneta, OH
What about a 5/8" spade bit and grind it down? Cut the spur back some as well. Might be easier to get to .6" with it.
I started with absolutely nothing. Now, thanks to years of hard work, careful planning, and perseverance, I find I still have most of it left.
Posts: 12,870
Threads: 0
Joined: Jan 2010
Location: Lewiston, NY
(10-30-2024, 09:08 AM)fredhargis Wrote: What about a 5/8" spade bit and grind it down? Cut the spur back some as well. Might be easier to get to .6" with it.
^^^^ Should be a pretty straight forward process and if you screw one up it's not a big loss.
John
Posts: 2,574
Threads: 0
Joined: Feb 2001
(10-30-2024, 09:08 AM)fredhargis Wrote: What about a 5/8" spade bit and grind it down? Cut the spur back some as well. Might be easier to get to .6" with it.
That’s a thought, but I haven’t had much luck with getting clean holes with a spade bit, and wouldn’t grinding that much off take off the cutting part of the bit off?
Posts: 1,872
Threads: 0
Joined: Feb 2006
Location: Eastern WA
Just a couple holes, right? I would use the 15mm bit, then use a large dowel wrapped in sandpaper, and sand off the edges enough for the hinge to fit. Use a marker on the inside of the hole, so you know what areas to sand off.
Posts: 2,574
Threads: 0
Joined: Feb 2001
(10-30-2024, 09:44 AM)rschissler Wrote: Just a couple holes, right? I would use the 15mm bit, then use a large dowel wrapped in sandpaper, and sand off the edges enough for the hinge to fit. Use a marker on the inside of the hole, so you know what areas to sand off.
If it was just a couple, I might do that, but I have 56 sewing machines and several of them would be better in portable boxes when looking for a new home.
I have also thought of making a router jig that clamps to the box and use that to enlarge the hole, but if I can find or make a forstner type bit I think I will be better off not going through several steps to make the same hole.
I suppose the other option since I have several, is to program my CNC to do it.
Duke
Posts: 5,180
Threads: 0
Joined: Jan 2014
Location: Santa Maria, Ca
Jig for a router bit is what I would use. But then, I have no CNC capability.
Mark Singleton
Bene vivendo est optimum vindictae
The Laws of Physics do not care about your Politics - Me
Posts: 12,870
Threads: 0
Joined: Jan 2010
Location: Lewiston, NY
(10-30-2024, 09:51 AM)JDuke Wrote: If it was just a couple, I might do that, but I have 56 sewing machines and several of them would be better in portable boxes when looking for a new home.
I have also thought of making a router jig that clamps to the box and use that to enlarge the hole, but if I can find or make a forstner type bit I think I will be better off not going through several steps to make the same hole.
I suppose the other option since I have several, is to program my CNC to do it.
Duke
If you have a CNC and the parts are easily indexed on it, then it's a done deal for me.
John
Posts: 4,644
Threads: 0
Joined: Jan 2008
might want find a machine shop that can chuck the bit in a lathe and turn it to size.
Posts: 2,574
Threads: 0
Joined: Feb 2001
I have a metal lathe, I’ll just have to come up with a makeshift tool post grinder.
