Posts: 12,283
Threads: 0
Joined: Jun 2007
Location: Bucks County PA
After nearly falling over several times trying to contort myself to reach the ON/OFF switch I'm thinking of getting a remote for my newly installed 3HP DC. I was going to go with the one from PSI but it says it for DCs up to 2HP.
A quick search showed me THIS one sold by Grizzly
T26674 240V Dust Collection Remote Any comments about this one or maybe suggestion on another type?
See ya around,
Dominic
------------------------------
Don't you love it when you ask someone what time it is and to prove how smart they are, they tell you how to build a watch?
Posts: 2,217
Threads: 0
Joined: Nov 2007
here are a couple more at grizzly.
http://www.grizzly.com/catalog/2014/Main/208 they are more money. the long ranger has been around for a while. I have been using a shop fox, the 110v version, for 8 or 9 yrs. it has been so long I forget when I bought it. The shop fox has worked perfectly plus you get two remotes. In that time I have had to change the batteries once. Grizzly used to carry the shop fox remote but I couldn't find it. SF does have a 220v version.
Posts: 12,283
Threads: 0
Joined: Jun 2007
Location: Bucks County PA
The 220V version of the Long Ranger only has a capacity of 2 to 2.5 HP. My DC is 3HP
The other Grizzly Remote you linked to has this note in it's advertisement. "Not available for immediate shipment". So I'm thinking that this may the older version of the one I linked to.
I just Googled "Remote for 3HP Dust Collector" and came across this one:
WoodRiver 220-Volt Dust Collector Remote Control Switch" for $88.99
See ya around,
Dominic
------------------------------
Don't you love it when you ask someone what time it is and to prove how smart they are, they tell you how to build a watch?
Posts: 30,422
Threads: 1
Joined: Dec 2002
Location: IL or NC <coin toss>
http://www.pennstateind.com/store/LR2244.html 
Quote:
Can be wired for
220-230V up to 19 amps single phase (up to 3.5 HP)
220-230V - up to 19 amps 3 phase (up to 5HP
440-450V - up to 19 amps 3 phase (up to 7.5 HP
Posts: 12,610
Threads: 0
Joined: Aug 2003
Location: Wapakoneta, OH
You'll have one that will last your lifetime if you get a 240V contacter, set it up to switch the DC and then switch the contacter with one of those cheap lamp remotes ($10). I built mine for probably less than $40 about 56 years ago. Since that time I've had 2 of the remotes fail (which is what happened to my Long Ranger at 10 years and my Shop fox at 1 year) and I keep a spare on hand. Switch it out and your back in business. The contacters are industrial grade and can be had to power any size motor (mines a 40 amp). They can be had at any industrial supply or from Clear Vue. Then all you need is some wire, a box to hold the contacter, and the switch. If this setup has any downside at all, there needs to be a 120V outlet near wherever the contacter is mounted for the lamp remote. In the pic, you see the gray box behind the DC....that's what I put mine in. You also see the 240V wire running into and out of the gray box (an exterior electrical box) and the small lamp cord underneath for the lamp switch.
I started with absolutely nothing. Now, thanks to years of hard work, careful planning, and perseverance, I find I still have most of it left.
Posts: 30,422
Threads: 1
Joined: Dec 2002
Location: IL or NC <coin toss>
Fred -
I'm sorta in the same boat. My remote for my 2hp Oneida failed (seems like a common fault), so I have just been powering off and on manually via the mag switch. I do miss the remote though. I was seriously considering buying the all-in-one 220V Lone Ranger setup I linked above, but your homebrew remote idea (again) has piqued my interest. Do you have a link to a wiring diagram and parts list somewhere?
Posts: 6,759
Threads: 2
Joined: Dec 1999
IIRC you have the same Reliant DC as I do. I had the same problem but, being cheap, took a different approach. I put a small eye bolt on the switch and attached it to a dowel which comes up and through another larger eye bolt as a guide. No more bending over.
Ken
Carolyn "Kscott & GDay, can I come sniff you?"
Timberwolf "You ARE WHO you eat"!!!!!!! "
Spokeshave "You're swallowing someone else's DNA right now."
Posts: 24,819
Threads: 0
Joined: Dec 2008
+1
I made my own about 10 years ago.
Posts: 16,649
Threads: 2
Joined: Oct 1999
+1 on the Long Ranger remote! I've been using one on my Penn State 2 1/2 HP 220V double bagger for >10 years now with no problem whatsoever.
Doug
Posts: 816
Threads: 0
Joined: Aug 2000
I did the same thing Fred did and have been on the same cheap lamp remote for about three years now. I saved a spring clip from a broken tape measure and screwed it to the back of the remote, so its attached to my shop apron and always handy. Keeps it from being knocked around, too. My D/C has a 5 hp motor and haven't had any problems with the contactor.
