Posts: 872
Threads: 0
Joined: Sep 2006
This is my first post in hand tools. I'm looking for a recommended plane to clean up these dovetails. I have used the edge sander in the past, but it is too easy to make a mistake that way.
Not just the type of plane, but if you could recommend actual make/model that would be great. I know planes can go for a lot of money, but I am looking to spend a modest amount. This will be my first plane. Thanks.
Posts: 9,928
Threads: 1
Joined: Apr 2005
Location: Texas
You need a low angle block plane.
LN would be my recommendation.
Also, an LN62 would work.
Plane from the front of the drawer towards the rear.
Next time, make the drawer sides proud of the front. It is easier to plane face grain rather than end grain.
...Naval Aviators, that had balz made of brass and the size of bowling balls, getting shot off the deck at night, in heavy seas, hoping that when they leave the deck that the ship is pointed towards the sky and not the water.
AD1 T. O. Cronkhite
Posts: 22,506
Threads: 0
Joined: Feb 2005
Location: Regina Saskatchewan Canada
You do need a low angle block. I would steer you to the Lee valley offering. But...... ( yes there is one, even if you wished otherwise).
You need some way to sharpen said block plane and that's were things get hairy. Not because sharpening is all that difficult but all the differing advise and options out there.
Blackhat
Bad experiences come from poor decisions. So do good stories.
Posts: 2,768
Threads: 0
Joined: Oct 2012
Location: W. of Rainier, E. of Orcas
You aren't building a jewelry box, hopefully. My preference is to build as you have, with a proud front lap, given the nightmare of fitting fat side boards several times through a few recycled seasons. Fit the guide(s) snug. Nibble down the lap to fit the carcase tightly, and flush the pins to the side board. When you adjust fit there is only a little end grain to fuss over.
You can use just about anything to flush the pins. Chisel, surform tool, rasp, and a shoulder plane; if you really need a plane. Or, a side rabbet, maybe a No. 4.
But ultimately, I would buy a Leigh-Nielson 102 bronze (cute factor only in the bib apron pocket) and drop the pins onto your belt sander at normal juice speed.
Posts: 872
Threads: 0
Joined: Sep 2006
Thanks for the advice so far. I do have a worksharp 3000, which I use for my chisels and turning tools.
Posts: 6,674
Threads: 1
Joined: Jan 2003
Location: Southern California
In terms of new: either the LV or LN low angle black planes. In terms of used: there are several folks around here who regularly sell older, used block planes. Send a PM to Admiral or Gregory of Sherwood Forest or JClark. Any of these reputable folks will fix you up at a price of <= 1/2 new - more or less.
Your Worksharp will do for honing the blade.
Thanks, Curt
-----------------
"Life can only be understood backwards; but it must be lived forwards."
-- Soren Kierkegaard
Posts: 21,254
Threads: 2
Joined: Mar 2009
Location: IA
I would also suggest practicing on another piece of wood instead of your project first.
Arlin
As of this time I am not teaching vets to turn. Also please do not send any items to me without prior notification. Thank You Everyone.
It is always the right time, to do the right thing.
Posts: 479
Threads: 0
Joined: Jul 2004
Sand paper and a wood block is a hand tool also
Posts: 2,258
Threads: 0
Joined: Dec 2007
Any plane will do. As long as the edge is sharp. The latter is way more important then the type of plane. I do this kind of work with a Stanley #4, skewing the plane slightly.
When you can't afford LN or LV, and you don't want to refurbish an old Stanley, then the offerings from Woodriver are a good choice. Those are perfectly allright planes.
Posts: 10,118
Threads: 0
Joined: Sep 2006
Location: South Alabama
A block plane would be good. So would a smoothing plane, such as a vintage Stanley #3 or #4. I would typically use my Stanely 4 1/2 smoothing plane for that job because it's what I have.
You might also consider the Veritas low-angle smoothing plane. I think you'd find it a welcome addition to your tool kit.
FWIW, Lee Valley has free shipping until the 31st, so if you're going to pull the trigger on a Veritas, now is a good time.
Veritas low-angle smoother Veritas low-angle block plane
Steve S.
------------------------------------------------------
Tradition cannot be inherited, and if you want it you must obtain it by great labour.
- T. S. Eliot
Tutorials and Build-Alongs at
The Literary Workshop