Where to find a replacement electrical triple tap?
#11
Triple tap??? Maybe I'm using the incorrect search term, but I've checked on Granger and a few other online electrical supply places, and I can't find one. I've purchased one previously at a local electrical place, but they went out of business and I haven't had any luck at Lowe's, HD, or Ace.

I have yards and yards of leftover electrical wire for 110v and want to make a few extension cords as I have about a half dozen of the do-it-yourself plugs (male end). I also have several single outlets (female end). I also want to make a couple with a triple tap (three female receptacles in one housing).

Is my search term incorrect? Anyone know where to get the do-it-yourself triple tap end?

Using this pic as a reference, the part I need is the triple tap female end.



[Image: p-SPM6410451403?plpSellerId=UnbeatableSa...#Imagezoom]


Attached Files Image(s)
   
" The founding fathers weren't trying to protect citizens' rights to have an interesting hobby." I Learn Each Day 1/18/13

www.RUSTHUNTER.com
Reply
#12
Does it have to be directly wired? I bought a triple tap adapter--one make, 3 female--at Home Depot for about $5.

http://www.homedepot.com/p/GE-15-Amp-125.../203735807
Reply
#13
Could you just use the triple outlet adapter from HF and cut the end off to attach to your cord?
Not an elegant solution, but it should work.
http://t.harborfreight.com/three-way-gro...20provided
Reply
#14
That was my preference, yes. I have a few of those adapters, but they don't hold on very well.

If all else fails, I'll just use standard galvanized steel electrical boxes, but I've been so happy with the one I have done in the past, that I wanted to do a couple more. I even looked at the one I have and it doesn't have any identifying markings on it except "Standard", "20A" and "American". Nothing that a search is helping find.
" The founding fathers weren't trying to protect citizens' rights to have an interesting hobby." I Learn Each Day 1/18/13

www.RUSTHUNTER.com
Reply
#15
I use a 2 gang box, with 2, duplex outlets. Cheap, rugged, and outlets can be replaced.
http://www.lowes.com/pd/Raco-2-Gang-Gray...ox/1098475

http://www.lowes.com/pd/Raco-2-Gang-Squa...r/50053659

http://www.lowes.com/pd/Eaton-15-Amp-125...et/1098367
I long for the days when Coke was a soft drink, and Black and Decker was a quality tool.
Happiness is a snipe free planer
Reply
#16
(09-22-2016, 06:10 AM)Pirate Wrote: I use a 2 gang box, with 2, duplex outlets. Cheap, rugged, and outlets can be replaced.
http://www.lowes.com/pd/Raco-2-Gang-Gray...ox/1098475

http://www.lowes.com/pd/Raco-2-Gang-Squa...r/50053659

http://www.lowes.com/pd/Eaton-15-Amp-125...et/1098367

+1 - For a homemade solution, this is what i recommend as well.  If you wanted a store bought version of a completed cord, they are readily available at the big box stores they may just be sold out, but I am not aware of any options for those wanting to put a replacement triple tap onto an existing extension cord, if there is, you would likely find it on McMaster's web site. Unless you will be using this cord on a jobsite or at work or wherever you may get audited by OSHA, I would recommend just getting a store bought triple tap extension cord.  If you are just using this at home, I would go the homemade route.  Two modifications to the above recommendation is, I would use one of those sealed, outdoor boxes and I would use a cord grip to attach the cords to the box.  A third modification you might want to consider would be to use a GFCI receptacle to add a bit more safety to the homemade contraption, but that's optional, especially if you are mostly going to use it with a GFCI outlet.

2 Gang Exterior Box
http://www.homedepot.com/p/2-Gang-Weathe.../204208021

Cord Grip (note:  comes in two sizes, get the size that best fits your cord):
http://www.homedepot.com/p/3-4-in-Strain.../100126837

Paul
Paul
They were right, I SHOULDN'T have tried it at home!
Reply
#17
If the 2 gang solution doesn't provide enough outlets, you could go with a 4 gang box and 2 duplexes. I've seen that done, and it's a little heavy for my uses, so I've always stuck to the 2 gang.
I started with absolutely nothing. Now, thanks to years of hard work, careful planning, and perseverance, I find I still have most of it left.
Reply
#18
I have two cords I made.  They have a yellow rubber box on the ends.  The box holds two duplexes.   So it's a quadtap.   I don't know where you can get them.  I've had them for 25 years.
RP
I just looked for them. Woodhead makes them. They're expensive. Amazon has them.
Reply
#19
my dad had a duplex box on the end of some romex he used as an extension cord for the longest time.  I like to put a woven cable grip/strain relief on the box, but of course by that time you are into it for $$
Reply
#20
My solution

[Image: 20160922_102005_zpskw0oxrl1.jpg]


[Image: 20160922_101943_zps9smtkevx.jpg]


[Image: 20160922_102032_zpsp5rqkfev.jpg]

The main reason for using an existing three or five way tap. It is  easy to replace when the triple tap outlets fail. I push the white button remove the tap and get a new one......  Poors mans solution: get a three way tape plug in and wrap with  electrical tape it to the cord/receptacle  works just fine
Let us not seek the Republican Answer , or the Democratic answer. Let us not seek to fix the blame for the past. Let us accept our own responsibility for the future  John F. Kennedy 



Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.