Posts: 15,331
Threads: 0
Joined: Jan 2005
I have custom hickory cabinets in my kitchen from 24 yrs ago. The cabinets have a 70" tall opening for the refrigerator. I had to replace my very old refrigerator and the one that LOML had to have was exactly 70" tall and the new frig will not physically go back into the opening. Period, won't go.
I'm going to zip off 5/16" or so of that rail for clearance and scoot it on back.
Using the appropriate clamping straight edge:
Would you use a fine blade and the Bosch jig saw (which I own)?
Or, go buy a compact router (cause I don't have a small one) and rout it?
I have a large PC 892 but since this is vertical and not horizontal, I'm afraid of losing control of something that size.
Advice please. Pour it on.
Thanks
This isn't a woodworking group, its a group of mostly imbeciles and retards. FearMonger 8-Feb-2012
If God had a sidearm, it'd be a 1911.
Posts: 4,519
Threads: 0
Joined: Jan 2008
think id take the cabinet off the wall and work on it safely to start.
Posts: 15,331
Threads: 0
Joined: Jan 2005
09-22-2016, 08:05 AM
(This post was last modified: 09-22-2016, 08:19 AM by Imakmst©.)
It's a one piece floor to ceiling unit that can't come down
I need to take some off the rail leaving the stiles alone, like where the arrow is pointing.
Posts: 13,400
Threads: 4
Joined: Jun 2007
Location: New Jersey
Assuming that the shelf above the rail is not the thickness of the rail (i.e., you don't have to remove part of the bottom of the shelf), I think a small trim router is your best bet, with a sharp chisel to clean up the corners. Alternative is a oscillating saw plunged in from the front on a scribed line, but that's hard to control and to keep it a neat job. Depending on how the shelf is attached and if the rail is truly structual, I imagine you could remove the whole rail with an oscillating saw plunge at the side joints, then trim it down on your table saw, and glue back in, but that's major surgery.
Sounds like an opportunity to get a trim router.....
![Laugh Laugh](https://forums.woodnet.net/images/graemlins/yellowlaugh.gif)
I have and like the Bosch Colt.
Credo Elvem ipsum etiam vivere
Non impediti ratione cogitationis
Posts: 20,950
Threads: 0
Joined: May 2005
Colt is what we used to enlarge for a built-in dishwasher. Clamp your guide, use a bushing for straight.
Make the guide wide enough to take all the router base for stability.
Better to follow the leader than the pack. Less to step in.
Posts: 5,411
Threads: 0
Joined: Jun 2001
Location: Troy IL
If it was me in a clients home I'd use the jigsaw and sanding block. routers make lots of dust, you could clean up the cut with the router but 5/16 IS allot of dust. while you at it take 1/2"
Life is what you make of it, change your thinking, change your life!
Don's woodshop
Posts: 26,727
Threads: 0
Joined: Sep 2002
Location: The North Woods
I think that you will get a better edge with a router. I would start with a rabbet bit, ake a couple passes with that, then switch to a template bit to complete. Trim the corners with a chisel.
Macky
The wheel of Life is like a toilet-paper roll, the closer to the end you get, the faster it goes around.
Posts: 46,965
Threads: 0
Joined: Nov 2002
Location: east coaster
just a thought, but if ya go the trim router route and have difficulty clamping a guide on there, could always use a thin strip on the underside of the cabinet up against the lower rail. few pieces of double-sided tape just to hold in place, but might be easier than trying to clamp a guide on there.
of course, that's given that the face frame's mounted nicely square to the cabinet.
or . . . tracksawer!
Posts: 10,704
Threads: 1
Joined: Jan 2006
Location: Orlando, Florida
Are the legs on the fridge fully retracted? Most fridge legs are adjustable to level them out, and they default out of the factory to halfway out. I'd try that before I'd start cutting into my cabinets.
Still Learning,
Allan Hill
Posts: 1,407
Threads: 2
Joined: Jun 2003
Not an envious job.
If the rail extends below the bottom of the cab, you could use a pattern bit and trim it flush, then clean the corners up with a chisel and bull nose plane.
You can attach a filler strip to the bottom of the cab however thick you want the rail to be, 1/4" or so might do it.