Need advice on how to do something
#31
  Re: Need advice on how to do something by Imakmst© (I have custom hickor...)
I'd use a flush cut saw to cut up along each stile, a coping saw to take a couple inches off each end and a hand plane. Likely be finished before you clean up after a router or jigsaw.
Blackhat
Common decency is as rare as common sense. I figure there was only a finite amount of both made and its getting shared out among too many folks.


Reply
#32
  Re: Need advice on how to do something by Imakmst© (I have custom hickor...)
Last time I did one, I used a circular saw (in situ) and finished with a Dozuki. Of course, I used straight edge. Didn't worry about the pocket hole screws, but I did remove the ones I knew were in the way. I don't think I hit the rest of them. Its been a while.

The circ saw leaves a good finished edge and is way quicker than a router.
Rocket Science is more fun when you actually have rockets. 

"The Constitution is not an instrument for the government to restrain the people, it is an instrument for the people to restrain the government." -- Patrick Henry
Reply
#33
  Re: Need advice on how to do something by Imakmst© (I have custom hickor...)
(09-22-2016, 05:03 PM)Stwood_ Wrote: Probably risky skill sawing the rail completely out, due to possible metal.  Pocket screws perhaps, or brads.

Yeah, you gotta know if there are any in the way.  There were pocket screws on mine.
Reply
#34
  Re: RE: Need advice on how to do something by Stwood_ (Probably risky skill...)
It's easier, and perhaps cheaper just to buy a new fridge
Winkgrin
Macky

The wheel of Life is like a toilet-paper roll, the closer to the end you get, the faster it goes around.

Reply
#35
  Re: Need advice on how to do something by Imakmst© (I have custom hickor...)
(09-22-2016, 07:41 AM)Imakmst© Wrote: I have custom hickory cabinets in my kitchen from 24 yrs ago.  The cabinets have a 70" tall opening for the refrigerator.  I had to replace my very old refrigerator and the one that LOML had to have was exactly 70" tall and the new frig will not physically go back into the opening.  Period, won't go.

I'm going to zip off 5/16" or so of that rail for clearance and scoot it on back.

Using the appropriate clamping straight edge:

Would you use a fine blade and the Bosch jig saw (which I own)?
...

I'd tape the face of it, install a straight edge to guide your Bosch jig saw, but I'd definitely use a down cutting bit,

like they use for countertop openings.

That way, the teeth of the blade won't splinter your finished front edge.

But be advised, you have to push down on the saw, as the blade will be trying to push it away from the work.

It will be a near perfect cut using this method.

[Image: d6abcffd74f361bab7b7ac0f6c2354da.jpg]
[Image: usa-flag-waving-united-states-of-america...if-clr.gif]
Reply
#36
  Re: RE: Need advice on how to do something by barnowl ([quote='Imakmst©' pi...)
nice
Thanks Barn
Reply
#37
  Re: RE: Need advice on how to do something by Imakmst© (nice Thanks Barn...)
Happy to help Gerry.
[Image: usa-flag-waving-united-states-of-america...if-clr.gif]
Reply
#38
  Re: RE: Need advice on how to do something by barnowl (Happy to help Gerry....)
do you need to cut it all the way across or only to clear the hinge mounts?
Reply
#39
  Re: RE: Need advice on how to do something by Gary™ (do you need to cut i...)
all the way from stile to stile
Reply
#40
  Re: RE: Need advice on how to do something by Imakmst© (nice Thanks Barn...)
Turn off the orbital function if you use those blades.
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.