Carbide woodturning tools please see new thread
#11
  
please see new thread
https://www.forums.woodnet.net/showthrea...id=7327453



I have  Carbide wood turning tools that I make for sale.

These do not have any handles, you will have to provide your own.

Rougher 15mm x100mm (4") radius on 1/2" x 1/2" square 304 stainless steel 9" long with 2 " tang



Rougher 15mm x100mm (4") radius on 1/2 round tool steel bar



Finisher 16 mm round mounted on 1/2" x 1/2" square 304 stainless steel 9" long with 2 " tang



Finisher 16 mm round mounted on 1/2" round tool steel



Finisher 12mm Round 3/8 x 3/8 stainless steel bar 9" long. 2" tang


Finisher 12mm Round 3/8 round tool steel 9" long

I will have to update this one tonight don't have a photo uploaded. It is shown in the group picture.

Diamond Detailer 3/8 x 3/8 stainless steel bar 9" long. 2" tang



Diamond Detailer 3/8 round tool steel 9" long







Left to right in picture.


Rougher on 1/2" Stainless steel square bar $25 plus shipping
Rougher on 1/2" round tool steel bar $25 plus shipping

Finisher 16mm on 1/2" Stainless steel bar $30 plus shipping
Finisher 16mm on 1/2" round tool steel bar $30 plus shipping

Finisher 12 mm round on 3/8 Stainless steel bar $27 plus shipping
Finisher 12 mm round on 3/8 round tool steel bar$27 plus shipping

Diamond detailer on 3/8 Stainless steel bar $31 plus shipping
Diamond detailer on 3/8 round tool steel bar$31 plus shipping


I do have replacement inserts:
$5 each:
15mm x 15mmx 2"r (50mm)
15mm x 15mmx 4"r (100mm)
15mm x 15mmx 6"r (150mm)
15mm x 15mmx square

16mm $10.00
12mm $8.50
Diamond detailer $9

Shipping on the inserts is $.75 each first class mail if you want tracking that will additional.
If you buy one of the turning tools and extra inserts at the same time there is no extra for the shipping the inserts.





Custom lengths are available.

John
Reply
#12
  Re: Carbide woodturning tools please see new thread by jaustin (please see new threa...)
John

You need to turn on your PMs to receive any.

You can go to my post here to get it done
https://forums.woodnet.net/showthread.php?tid=7320581
It is always the right time, to do the right thing.

Hi, I'm Arlin's proud wife! His brain trma & meds-give memory probs and has pain from injuries, but all is well materially & financially.  
Reply
#13
  Re: Carbide woodturning tools please see new thread by jaustin (please see new threa...)
Thanks I think Igot it set now.

john
Reply
#14
  Re: RE: Reload this Page Carbide woodturning tools by jaustin (Thanks I think Igot ...)
Out of the 16mm insert and 16mm finishers tools are not available till sometime next week.

Have the 16mm inserts back in stock now.



Have everything else available.
Reply
#15
  Re: Carbide woodturning tools please see new thread by jaustin (please see new threa...)
Today I received my two tools I ordered from John today.  I received the 1/2" and 3/8" square cutters with the round heads on them.

They are just as described and I can not be happier.  When one of the vets or someone else I teach turning I try to give them some turning tools and a lathe if I have one so they can go off on their own.  So far I have done that with 6 of them and now I have another source to buy quality tools at a Wonderful price along with the carbide bits too.

Very happy customer and will get more in the future when I can afford it.

Arlin
It is always the right time, to do the right thing.

Hi, I'm Arlin's proud wife! His brain trma & meds-give memory probs and has pain from injuries, but all is well materially & financially.  
Reply
#16
  Re: Carbide woodturning tools please see new thread by jaustin (please see new threa...)
PM sent. 

Jeff
It's time for the patriots to stand up!
Reply
#17
  Re: Carbide woodturning tools please see new thread by jaustin (please see new threa...)
I would like to purchase one each of the larger tools and it was my intent to send you a PM, so as not to show my ignorance to the entire world, however, I cannot find my "CP", as someone directed to look in the upper left corner of the screen.  But, as far as I can see, there is no "CP" anywhere on my screen, which with my record with computers and internet is nothing usual.  Having said the above, my question I wanted to ask you, how do you press the tang into the hole? Or do you make the hole slightly larger and use epoxy?  Having never done this before I wanted to know before I purchased them.


Thank for your listening and if you know where my CP went would you let me know?
Herb
I'm supposed to respect my elders, but it's getting harder and harder for me to find one now.
Reply
#18
  Re: RE: Carbide woodturning tools by Herb (I would like to purc...)
Up at near the top.  See attachment.
[attachment=541]


Your Profile -> Edit Options  (see attachment)
[attachment=543]
Reply
#19
  Re: RE: Carbide woodturning tools by Herb (I would like to purc...)
Herb,
The tangs are a little undersized for the holes. You will use epoxy to attached the handle with the bar.then you will have to make sure the handle and tool are straight with each while it dries.
Example drill a hole and put epoxy around tang then insert it into handle and keep straight while it dries.

i would send you a message but they are off. Look at post #2 above Arlin posted instructions on turning them on.

https://forums.woodnet.net/showthread.php?tid=7320581

John
Reply
#20
  Re: RE: Carbide woodturning tools by fgarvin (Up at near the top. ...)
Here is my Welcome back and I see not CP.  I click on my name and there is nothing there that will let me edit my profile.  Clicking on my profile does nothing.
What am I missing?

[img=328x93]file:///C:/Users/LENOVO~1/AppData/Local/Temp/msohtmlclip1/01/clip_image001.png[/img]
 


Welcome back, Herb. You last visited: Yesterday, 01:47 AM Log Out
 
Woodnet Forums 
[img=15x15]file:///C:/Users/LENOVO~1/AppData/Local/Temp/msohtmlclip1/01/clip_image002.png[/img] Profile of Herb
Herb
(Member)


Registration Date: 2003-07-27
Date of Birth: Hidden 
Local Time: 2016-11-08 at 12:40 AM
Status: Online (Viewing Profile of Herb @ 12:39 AM) 
[img=100x100]file:///C:/Users/LENOVO~1/AppData/Local/Temp/msohtmlclip1/01/clip_image003.png[/img]
 
Herb's Forum Info
Joined:
2003-07-27
Last Visit:
Less than 1 minute ago
Total Posts:
478 (0.1 posts per day | 0.22 percent of total posts) 
(Find All Posts)
Total Threads:
0 (0 threads per day | 0 percent of total threads) 
(Find All Threads)
Members Referred:
0
 
Herb's Signature
Herb
I'm supposed to respect my elders, but it's getting harder and harder for me to find one now.
Herb
I'm supposed to respect my elders, but it's getting harder and harder for me to find one now.
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)