Posts: 12,606
Threads: 0
Joined: Aug 2003
Location: Wapakoneta, OH
I just remembered I need to run a wire to connect a future thermostat (not yet purchased) to a future furnace (ceiling hung Modine type, also not yet purchased) in my shop before any drywall work. This is a common heat on/off, low voltage, temperature control thermostat. I've installed 2 in the way past, but cannot remember what wire I ran. I know it's very thin (22 gauge?) but can't remember how many conductors are needed. But I know most of you out there know, maybe you can remind me.
I started with absolutely nothing. Now, thanks to years of hard work, careful planning, and perseverance, I find I still have most of it left.
Posts: 4,648
Threads: 0
Joined: Jan 2008
a roll of 18/5 should give ya enough conductors
Posts: 31,107
Threads: 2
Joined: Mar 2003
Location: Athens, TN
More conductors than you think or in the next replacement, you'll be running new.
Go on-line and get the install instructions and use that many wires, at least.
Rocket Science is more fun when you actually have rockets.
"The Constitution is not an instrument for the government to restrain the people, it is an instrument for the people to restrain the government." -- Patrick Henry
Posts: 13,412
Threads: 0
Joined: Jun 2004
Location: Texas
You shouldn't need more than three wires for heating only. I only buy 3 and 6 wire but use the 6 in places where you may never be able to replace it just in case a wire gets chewed on by a rodent or for some reason opens.
Posts: 22,711
Threads: 0
Joined: Feb 2005
Location: Regina Saskatchewan Canada
You need 2. R and W. 22 ga would but 18 is better. Running a 3 or 4 conductor just in case of a nail strike wouldn't hurt.
Blackhat
Bad experiences come from poor decisions. So do good stories.
Posts: 12,606
Threads: 0
Joined: Aug 2003
Location: Wapakoneta, OH
Thanks all, I'll pick up some 18 gauge 4 conductor.
I started with absolutely nothing. Now, thanks to years of hard work, careful planning, and perseverance, I find I still have most of it left.
Posts: 1,998
Threads: 1
Joined: Aug 2016
05-10-2017, 03:26 PM
(This post was last modified: 05-10-2017, 03:28 PM by Roly.)
Something else to think about is possibility using two thermostats for heating. A low temp thermostat to keep from freezing and a timer on the high temp thermostat for when occupied. We used this system for normally unoccupied control buildings. Roly ( uses the same wire )
Posts: 22,711
Threads: 0
Joined: Feb 2005
Location: Regina Saskatchewan Canada
I'm going to set up something similar with a motion sensor on the high temp stat. I need to get a time delay so it doesn't start when I walk through to drop trash in the can.
Blackhat
Bad experiences come from poor decisions. So do good stories.
Posts: 1,998
Threads: 1
Joined: Aug 2016
Something like
THIS for a time delay. Still need the motion detector part. This will reset when it looses voltage. Roly
Posts: 253
Threads: 0
Joined: Jun 2010
Best thing is to look and see how many wires you have now. If your upgrading, how many wires will you need? If you have an older Honeywell Merc Switch with older heater 2 wires. On some of the newer units if its heat and AC 4-5 wires may be enough. Go to the BORG and get thermostat wire with the number of wires needed 18 gauge/ # of wires inside, from 2-8. Make sure you get more wire than you think you need. It sucks coming up short.
