Next Project
#41
Nice posting, my shop skills and such doesn't allow furniture woodworking but I enjoyed your progress.
What the Heck, Give it a Try
Reply
#42
Went back  to the shop last night....started working on that lid
   
Made a full sized template, for the joint where the lid and top shelf meet...
   
needed to go from this "thing" to ..
   
this.   Templates set the degree of bevel I needed to rip.   Set up a guide for the saw to follow
   
Hey, that saw is as old as I am..Vintage saw, right?    Will come back later, and clean the saw marks up with a plane. 
   
Looks like I have quite a few to hit with the planes....includes a "book rest" lip for books to rest against. 

Shop is usually closed on Mondays,  maybe get back to work on Tuesday?  
Winkgrin




Show me a picture, I'll build a project from that
Reply
#43
Snuck into the shop last night..I got bored....
Uhoh

All the edges that needed planed, were done...
   
Beveled and non-beveled edges got  jointered..
   
Flat work done as well.   Got the Book Rest sized, and planed smooth
   
Had to double check that I glued it to the correct face of the lid.  Used a small-ish  plane for most of the work..
   
Though there were a few spots that needed the wee ones..
   
The end grain on the top shelf needed that little block plane. 

Need to meander down to the shop, and remove some clamps, and start cleaning up glue joints, including all the dovetailed corners..might be some cussing involved..
Upset
Uhoh
Yes

Stay tuned, I might get to the finish yet, inspite of meself..
Rolleyes
Show me a picture, I'll build a project from that
Reply
#44
Hey, don't make fun of the C-saw *I* bought new..... And, carbide tip blades are close to a dime a dozen. I get one every time I waste a trip to Hme Despot. Then make weird-strange tools from the old dull ones...
Reply
#45
Clamps came off, edge was planed..
   
Dovetails cleaned up and leveled, small..
   
and the large ends..
   
Gap in the bottom ofthe case was fillered in..
   
Got those high spot along the edges of the stand leveled out.   Decided to set things up, to see how it all will look..
   
Waiting on Friday to buy some hinges, and a finish to apply....Starting to look like a desk, now...

Stay tuned...
Show me a picture, I'll build a project from that
Reply
#46
Hinges were bought, and installed..(I hate hinge work
Angry )
   
Walnut plug made, and glued in place, waiting on the glue to dry, before I trim them flush
   
Hinges seem to work nicely.
Cool
   
Closed the lid, and did a test run of BLO on just the lid  ( BLO STINKS
Upset )
   
Placed the desk back out of the way, for now..
   
And clear the bench of tools.  

Will need to find a spot I can do the finishing in.....a little cramped down there.    IF the rain would hold off a day or two, I can do the BLO outside on the back patio...

Stay tuned, almost done.
Winkgrin
Show me a picture, I'll build a project from that
Reply
#47
Tried a different camera, as things were coming out too yellow..
No
   
Hmm, may need to turn the flash ON?
Rolleyes
   
Ah, that's better...
Cool One more?
   
Might use this older camera to post the finished project
Yes
Show me a picture, I'll build a project from that
Reply
#48
Yellow pee colored pics look better from this end.
Raised
Steve

Mo.



I miss the days of using my dinghy with a girlfriend too. Zack Butler-4/18/24


 
The Revos apparently are designed to clamp railroad ties and pull together horrifically prepared joints
WaterlooMark 02/9/2020








Reply
#49
Are you planning to rest your wrists against that tall "pencil stop" when using the desk?

I really like standing desks and one has been on my list for a while now. Getting some ideas, especially the H stretcher configuration.
Don't sweat the petty things and don't pet the sweaty things. -- G. Carlin
Reply
#50
The "Pencil stop" is more to stop a large book from sliding off the lid.  

Desk has been hauled up the stairs....just in time..
Upset
   
This is where it WAS sitting
Uhoh
   
Washer's drain pipe wasn't letting all the water run past it...had to yank the pipe out, and listen to the whirlpool sound as almost 2" of water went down the drain.
No  
Huge Thunderstorm was going by,  there is now a pond between my house and the neighbor's place....wasn't there a while ago...running through the shop, now..
   
Maybe tomorrow I can work in the shop?
Rolleyes
Show me a picture, I'll build a project from that
Reply


Forum Jump:


Users browsing this thread: 2 Guest(s)

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.