What did I do wrong ??
#9
I restored a Garden Bench and it came out great
I sandblasted the cast iron sides and back insert
and replaced the wood with White oak. For the
finish I was told to use Watco Teak Oil 
When it was finished it looked great.
And the great look lasted until the first rain,
A very light rain, that only got the seat slates wet.
After the rain I checked it and found that seat slats
where all covered something black that looked like mold
that I could not take off, even using a scouring pad.
I thought that I did everything right, planning the wood,
sanding it and applying the teak oil,  evidently I screwed
up somewhere.

What did I do wrong ??   
Reply
#10
Poor choice in wood.
Cellulose runs through my veins!
Reply
#11
I wouldn't blame the wood, white oak should be good for that purpose. But whoever told you to use the "teak oil" probably could have suggested something better. Not sure what the black is, but I'm guessing it's mildew. My approach would be to remove the finsh (on both the seat and back slats) and start over. My choice of a finish would be untinted exterior paint....but others here have had good luck with some other outdoor finishes, and they will be along to suggest them (and possibly offer a different diagnosis). For the "teak oil', there is no such thing and Flexner wrote a short article in PWW blasting the manufacturers for marketing such stuff.....it's little more than some other product they make in a different can. The Watco stuff is likely just a very thin varnish, or something else. If the untinted paint interest you, here's a little more info on it.
I started with absolutely nothing. Now, thanks to years of hard work, careful planning, and perseverance, I find I still have most of it left.
Reply
#12
If you want the wood grain to show through then a good spar varnish.  A good spar varnish is more flexible (and less hard) than regular varnish to accommodate the wood movement due to temperature and humidity changes outdoors.  

But you still want to stick with regular varnishes and urethanes indoors as they are harder and resist wear better.

I've never used these, but they are standard in the marine industry.

https://www.epifanes.com/page/clear-finishes

http://www.pettitpaint.com/product.asp?id=61
No animals were injured or killed in the production of this post.
Reply
#13
(09-19-2017, 08:46 PM)MIKE28 Wrote: I restored a Garden Bench and it came out great
I sandblasted the cast iron sides and back insert
and replaced the wood with White oak. For the
finish I was told to use Watco Teak Oil 
When it was finished it looked great.
And the great look lasted until the first rain,
A very light rain, that only got the seat slates wet.
After the rain I checked it and found that seat slats
where all covered something black that looked like mold
that I could not take off, even using a scouring pad.
I thought that I did everything right, planning the wood,
sanding it and applying the teak oil,  evidently I screwed
up somewhere.

What did I do wrong ??   

The black is mold/mildew.  I would power wash it and then treat the wood with a deck stripper/cleaner/brightener to bring the wood back to its original color.  White oak is a very rot resistant wood, but it will turn grey/black if it's not encapsulated in a film finish.  As others have said, the oil finish you used won't do that, you need to use one of the products already mentioned.  I have used Epifanes with good success but I'm sure the untinted exterior paint would work well, too. 

Keep in mind, once you put wood outdoors you are committed to routine maintenance no matter what finish you put on it.  With Epifanes you might get 2 or 3 years before having to address any cracks in the finish and applying another couple of three coats.  Same for any finish.  The only way to avoid routine maintenance is to use no finish at all and let the wood weather to it's natural gray/black. 

John
Reply
#14
Oak reacts to iron, and turns black. Could that be the problem here? How about some pics, to tell just where the black is.
Steve

Mo.



I miss the days of using my dinghy with a girlfriend too. Zack Butler-4/18/24


 
The Revos apparently are designed to clamp railroad ties and pull together horrifically prepared joints
WaterlooMark 02/9/2020








Reply
#15
I have wooden chairs I made subjected to getting damp and sometimes wet under the patio and partial sunlight. I used regular ole poly on them. 3 years on them and they just now need a touch up coat. If it is in the sun a lot, it will wear quicker.
I had worse luck with spar varnish- pealed and cracked the first year.

You have mildew. If you like the old look, just sand and re-coat.
Reply
#16
I had the same thing happen with a cypress table and BLO finish.  Mold/mildew seems to like the oil finishes.
Careful with the power wash.  It is easy to gouge out the soft wood parts.
They told me anybody could do it, but I showed them.
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.