Idea of a Project
#28
  Re: Idea of a Project by bandit571 (Might be the Dr. Fee...)
Taking today off. Winkgrin ...bills and van need seen to. Upset   May see about later... Uhoh
Show me a picture, I'll build a project from that
Reply
#29
  Re: Idea of a Project by bandit571 (Might be the Dr. Fee...)
ER Friday night. No .stomach issues.....just got back home a little while ago, today.....hemotoma  where the Gall bladder USED to be....meds to take care of things

Release will no restrictions, have to see the Doctor later this week. Cool
Show me a picture, I'll build a project from that
Reply
#30
  Re: Idea of a Project by bandit571 (Might be the Dr. Fee...)
(02-17-2019, 06:38 PM)bandit571 Wrote: ER Friday night. No .stomach issues.....just got back home a little while ago, today.....hemotoma  where the Gall bladder USED to be....meds to take care of things

Release will no restrictions, have to see the Doctor later this week. Cool

TAKE IT EASY, OK?
If you continue to cut corners, you'll end up going in circles!

It's my thumb so I'll hit it if I want to!
Reply
#31
  Re: Idea of a Project by bandit571 (Might be the Dr. Fee...)
Gad..........rest up
Steve


Putzing, the new hobby

Evil lurks here, but eventually gets cleansed.


Reply
#32
  Re: Idea of a Project by bandit571 (Might be the Dr. Fee...)
Well....instead of 6 hour shop days...I am keeping things to a single task, then calling it a day....Physical Therapy.... Rolleyes 

Today's task was to mill two 2 x 4 x 8' boards down to 4 corner posts.   4/4 x 3" x 43", and mill a few rebates. Rolleyes 
   
Cut to length.   I saved one of the cut-offs, to use as a set-up block.  needed to rip the rounded edge off one edge..
   
used the block to set the fence, blade did not raise high enough, had to flip the boards over, to complete that cut...
   
Then reset the fence to get things to 3" wide..
   
Next step was to get these down to 1" thickness...there was a slight problem..
   
Hmmm, well..I do have a brand new blade for the bandsaw....install that, and finish the cuts..
   
Then run the four posts through the saws....leaving the ridge to be planed off..
   
Millers Falls No. 11    Planed flat and smooth...now for a few rebates..
These four are for the rails and plywood panels to sit into...takes two set ups on the saw ( not up to doing this by hand, right now) then there are two rebates for the back panel to sit in...
   
Will need to clean these up...

Need to use one webframe, to lay out the drawer openings, to where I can attach the rails, and find the sizes for the panels...first, I need to cut a couple 1 x 4s down.   two at 26" long ( best of the two boards) and the rest at 13" or so.  Then they will get ripped for width.   Rails get a few rebates milled...maybe tomorrow? Confused  
   
Big knots are going "bye-bye" Cool
Stay tuned,,,one day at a time... Winkgrin


Attached Files Image(s)
   
Show me a picture, I'll build a project from that
Reply
#33
  Re: RE: Idea of a Project by bandit571 (Well....instead of 6...)
(7 hours ago)bandit571 Wrote: Well....instead of 6 hour shop days...I am keeping things to a single task, then calling it a day....Physical Therapy.... Rolleyes .....................................

...............................Stay tuned,,,one day at a time... Winkgrin

Show us your time card Wink
I'm watching you from near & afar. Rolleyes

BTW...good progress. Big Grin
If you continue to cut corners, you'll end up going in circles!

It's my thumb so I'll hit it if I want to!
Reply
#34
  Re: Idea of a Project by bandit571 (Might be the Dr. Fee...)
Have to wait until tomorrow for the pictures, but...due to a lack of time the rest of the week, went ahead and milled all the rails for both sides of the case.   Winkgrin 

IF I get back to the shop....I can start on a bit of lay out work....might even a little assembly?  We'll see.   Look for a few pictures in the morning... Cool
Show me a picture, I'll build a project from that
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)