Posts: 4,032
Threads: 0
Joined: Nov 2010
06-17-2019, 05:32 PM
have a bunch of the "normal" bits for brace drills.....2 or three sets...However, I have this "other" set..
Been using the two countersinks a lot...and a few of the skinnier ones for pilot holes....thinking these are more for drilling metal...
Now, there is also these 5 bits in the shop, snuck in via a box lot, one day...
That do not match anything I use in the shop.....any ideas? Most have a "Morse" New Bedford Mass "High-speed CO"
All these are doing is rusting....would rather someone who could use them.....
Show me a picture, I'll build a project from that
Posts: 741
Threads: 0
Joined: Mar 2006
Those are morse taper bits. Older drill presses often used those.
Posts: 3,017
Threads: 1
Joined: Aug 2009
06-17-2019, 08:37 PM
(This post was last modified: 06-17-2019, 08:40 PM by Bill_Houghton.)
Morse taper bits were also used in lathes - tailstock or headstock, depending on the job being done. There are people who use them. Put them up on a machinist's site, if you can find one with a buy/sell forum; or put them up here and see what happens.
Those twist bits were, most likely, intended for metal, although maybe not so much for the modern metals - they're not likely high speed steel.
Posts: 24,145
Threads: 2
Joined: Sep 2003
Location: Missouri
Yes. Very popular with the machinists
Steve
Mo.
I miss the days of using my dinghy with a girlfriend too. Zack Butler-4/18/24
The Revos apparently are designed to clamp railroad ties and pull together horrifically prepared joints
WaterlooMark 02/9/2020
Posts: 1,694
Threads: 0
Joined: Feb 2011
(06-17-2019, 08:48 PM)Stwood_ Wrote: Yes. Very popular with the machinists
What sizes are they? Do you now what the taper is off hand?
BontzSawWorks.net
Posts: 4,032
Threads: 0
Joined: Nov 2010
35/64", 15/32"....morse#2...
smaller one seems to be marked as 4/16" #1 taper ( Chicago Latrobe?)
middle 2 seem to be different...logo has a diamond over "MAJOR" and has an "H" "S" in the box with the diamond.
Ring a bell?
Show me a picture, I'll build a project from that
Posts: 116,261
Threads: 0
Joined: Jun 2002
Location: Sparkling Clearwater, Fl. Tampa Bay Area
(06-17-2019, 05:32 PM)bandit571 Wrote: have a bunch of the "normal" bits for brace drills.....2 or three sets...However, I have this "other" set..
Been using the two countersinks a lot...and a few of the skinnier ones for pilot holes....thinking these are more for drilling metal...
Now, there is also these 5 bits in the shop, snuck in via a box lot, one day...
That do not match anything I use in the shop.....any ideas? Most have a "Morse" New Bedford Mass "High-speed CO"
All these are doing is rusting....would rather someone who could use them.....
...................
Morse Twist Drill was located in New Bedford Ma. for many years and made quality industrial cutting tools.Well known for machinist tools..I have a set of #2 Morse taper shank drill for my South Bend Lathe..My late FIL worked at Morse many years ago.
Often Tested. Always Faithful. Brothers Forever
Jack Edgar, Sgt. U.S. Marines, Korea, America's Forgotten War
Get off my lawn !
Posts: 4,032
Threads: 0
Joined: Nov 2010
I can't use those tapered shank bits....doesn't fit into anything I have....would rather they go to someone who could put them to work.
..rather than sit in a drawer to rust..
..they will fit in a small flat rate box....
Show me a picture, I'll build a project from that
Posts: 30,580
Threads: 3
Joined: Sep 2003
Location: Saginaw, MI
Those bits fit my Atlas drill press. It’s an older press, at least 50 to 60 years old. I can’t help you though, as I have a full set from when I drilled bowling balls with it. Good luck in finding someone who can use them.
Jim
There is a good chance
Broccoli doesn’t like you either.
Posts: 1,513
Threads: 0
Joined: Mar 2006
Location: Berea, KY
Should not be too hard to find someone who can use them. I’m all set on bits also, but both my Delta drill press and my Jet lathe are MT #2, and they are around 15 years old. In other words, they are still making machinery that uses the #2 MT.
