Entry hall table for a niece
#28
The case was glued up yesterday, with everything tight and square as one could wish, but I did not sleep well. I was haunted by the thought that there was a problem that would come to a head some time in the future.

[Image: 17a.jpg]

If you look at the grain direction of the two centre drawer dividers, you notice that the grain is vertical. That is the way it should be. Wood moves, expands and contracts. It does this in reaction to moisture in the air. When it moves, it does so across the grain. That is why solid wood drawer bottoms have grain across the width - allowing the drawer bottom to move towards the back of the drawer, rather than towards the sides (where it will be blocked and then buckle).

These drawer dividers will be butted up against the rear of the drawer lips and act as drawer stops. The front third of the divider will be glued in the dado, forcing any expansion towards the rear of the case. All good.

The two spacers at the inside ends of the case have the grain running horizontally. I glued this in before I realised that I had cut them this way. I had done the same with the internal dividers, but re-cut them, as shown in the previous article. The end spacers will expand vertically, and to allow for this, I provided a 2mm gap below and above the panels. That is what kept me awake.

The end spacers are 6mm thick. The case, to which they are glued, is 20mm thick and about 40mm wider. Initially I was concerned that the spacer would be overwhelmed by the case moving, and buckle. Having thought some more about this, I am no longer concerned that this will occur. Why? Because movement in the case would instead "stretch" the spacer length-wise. I started to breath again.

In the end, I decided to reduce the height of the spacers by half. This would allow them plenty of space to expand, when necessary, as well as reducing their impact inside the case.

Here is one side ...

[Image: 1a.jpg]

Taped for visibility and protection ...

[Image: 2a.jpg]

The saw is a 16" Wenzloff & Sons tenon saw (10 tpi) ...

[Image: 3a.jpg]

Three kerfs ...

[Image: 4a.jpg]

Deepened with a Japanese Azebiki ...

[Image: 5a.jpg]

... and split out with a firmer chisel ...

[Image: 6a.jpg]

A Bahco carbide scraper cleans up ...

[Image: 7a.jpg]

The result ...

[Image: 8a.jpg]

[Image: 9a.jpg]

Final cleanup was aided by the only shoulder plane that fitted inside the space
Smile ...

[Image: 10a.jpg]

Regards from Perth

Derek
Articles on furniture building, shop made tools and tool reviews at www.inthewoodshop.com
Reply
#29
(02-02-2020, 08:03 AM)Timberwolf Wrote: ......................................
Woodworking doesn't get any better than this.......
No

Jack, there are a number of talented woodworkers out there but Derek is the only one I know who teaches, not only for free, but so well and for so many years now. I admire the man, his work and his talent.
Thanks,  Curt
-----------------
"Life can only be understood backwards; but it must be lived forwards."
      -- Soren Kierkegaard
Reply
#30
(02-03-2020, 08:46 PM)cputnam Wrote: Jack, there are a number of talented woodworkers out there but Derek is the only one I know who teaches, not only for free, but so well and for so many years now. I admire the man, his work and his talent.
Well said, and I couldn’t agree more!
Reply
#31
1+  

I can't say that I fully understand everything Derek describes, but I appreciate the effort.
Reply
#32
Derek,


As I said, before, thanks -- I am very much enjoying this build. I have a silly question, if you don't mind.

Jarrah is fairly brittle, isn't it? How do you repeatedly assemble and disassemble the body without chipping or dinging the edges of the dovetail pins or tails?
Best,
Aram, always learning

"Perfection is achieved, not when there is nothing more to add, but when there is nothing left to take away.” Antoine de Saint-Exupery


Web: My woodworking photo site
Reply
#33
Aram, the Jarrah does chip. I am relieved that it has not chipped more than it has, but there are a number of small chips I have to repair. This is typical, so I don't bother to even document it. The chips are filled with Jarrah shaped to match both the chip and the colour. At the end of the day they are invisible.

Regards from Perth

Derek
Articles on furniture building, shop made tools and tool reviews at www.inthewoodshop.com
Reply
#34
Thank you my dear friends who said all those nice things .... all lies I tell you
Smile

Regards from Perth

Derek
Articles on furniture building, shop made tools and tool reviews at www.inthewoodshop.com
Reply


Forum Jump:


Users browsing this thread: 2 Guest(s)

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.