Posts: 24,327
Threads: 0
Joined: Feb 2002
Location: Elizabethtown, KY
and rabbeted the hinges on the wrong edge of the door
"Truth is a highway leading to freedom" --Kris Kristofferson
Wild Turkey
We may see the writing on the wall, but all we do is criticize the handwriting.
(joined 10/1999)
Posts: 2,337
Threads: 0
Joined: Jan 2008
Location: Irving, Tx
Been there, done that. Bummer!!!!
"I tried being reasonable..........I didn't like it." Clint Eastwood
Posts: 23,952
Threads: 2
Joined: Sep 2003
Location: Missouri
Mmmm. Should have stopped at 4?
Steve
Mo.
I miss the days of using my dinghy with a girlfriend too. Zack Butler-4/18/24
The Revos apparently are designed to clamp railroad ties and pull together horrifically prepared joints
WaterlooMark 02/9/2020
Posts: 21,254
Threads: 2
Joined: Mar 2009
Location: IA
(03-24-2020, 04:53 PM)Wild Turkey Wrote: and rabbeted the hinges on the wrong edge of the door
Can you trim off the top and glue a piece in??
As of this time I am not teaching vets to turn. Also please do not send any items to me without prior notification. Thank You Everyone.
It is always the right time, to do the right thing.
Posts: 310
Threads: 0
Joined: Feb 2012
Location: Carson Valley, NV
Been there and done that myself. I made stiles for two doors and proceeded to drill cup holes in all of them
Posts: 4,439
Threads: 0
Joined: Jan 2005
(03-24-2020, 04:53 PM)Wild Turkey Wrote: and rabbeted the hinges on the wrong edge of the door
I was doing millwork and hanging doors on a commercial job. Doors were 3-0 x 7-0 x 2-1/4" thick cherry. I had a pair of doors that had flush bolts in the inactive door. After routing out the door for flush bolts and installing them .I hung the doors. I got sick realizing I had the flush bolts installed a--backwards. The bottom bolt was 12" off the floor and should have been 18" to the center. Top bolt was 18" to the center and should have been 12". I took off my overalls, packed up my tool box and told my boss I quit. He wanted to know why and I showed him the mistake. He laughed, then told me to get back to work because him and I were the only ones that knew.
He said if I did not point out the mistake he wouldn't know either.
mike
Posts: 12,457
Threads: 0
Joined: Aug 2003
Location: Wapakoneta, OH
What have you decided as a solution? (17)
I started with absolutely nothing. Now, thanks to years of hard work, careful planning, and perseverance, I find I still have most of it left.
Posts: 7,421
Threads: 1
Joined: Sep 2005
To the greatest extent possible I transfer dimensions directly to the mating pieces. Or I use a story stick.
For a door I would put it in place and then make a mark where the hinges would go.
Rulers don't think. Thinking has to be done before the ruler comes out.
No animals were injured or killed in the production of this post.
Posts: 2,375
Threads: 0
Joined: Dec 2011
The mistake was made because you broke the cardinal rule of....... measuring twice only!
Simon
Posts: 24,327
Threads: 0
Joined: Feb 2002
Location: Elizabethtown, KY
Routed edge smooth, cut other side correctly now will make spacer strip behind hinges
And keep my mouth shut!!!!
"Truth is a highway leading to freedom" --Kris Kristofferson
Wild Turkey
We may see the writing on the wall, but all we do is criticize the handwriting.
(joined 10/1999)
