Seeing the light....inside a bowl
#6
  
Ok, I can never seem to see inside the bowl or vessel I'm turning. Hunched over the lathe and struggling to see where the gouge is, seems to be the norm.
I've tried the light sold on WW and can never seem to get it in the right position to get light inside the bowl! Not to mention the goose neck is way too short and you hit your gouge handle on it if it's close enough to do any good.
I even tried that small led with magnets that is supposed to go on your tool rest; again, it won't stay and all the tool rests I have don't really have a flat spot to mount it, plus the bowl ends up rubbing the electric cord. The only thing I found good for general light is a chicken coop clamp light with a led flood light inside; but of course your body gets in the way when you are hollowing out the vessel. What do you guys/girls do for lighting??

   
   
   
Now where is that chisel
Reply
#7
  Re: Seeing the light....inside a bowl by Smashedfinger ([align=left]Ok, I ca...)
I stand up straight and turn toward the headstock, so a light from anywhere overhead or toward the tailstock area is all I need for open turnings.  For reduced entry types, I use my imagination and tactile/aural feedback, which is usually reliable enough.  My close work light is completely isolated from lathe vibration because it's mounted on the wall behind.  If you are not up against the wall, something on its own feet will keep your eyes from bouncing with the light.

Besides, the opposite side or lower inside looks like where you've been, so all gross removal can be done by looking there.  Standing upright and up front is the safe way, anyway.
Better to follow the leader than the pack. Less to step in.
Reply
#8
  Re: Seeing the light....inside a bowl by Smashedfinger ([align=left]Ok, I ca...)
I hung a 4,000 lumen LED light ($17 at Rural King) above my lathe and another on vertically at the end of and behind the lathe. Because these are not point sources, there is no shadow. I only turn the end one on when I'm working on the end of a piece because it's distracting otherwise. These work great and I highly recommend both the technique and the product.

By the way, please excuse the messy shop. Sometimes it's better organized than this.


Attached Files Image(s)
   
We do segmented turning, not because it is easy, but because it is hard.
Reply
#9
  Re: Seeing the light....inside a bowl by Smashedfinger ([align=left]Ok, I ca...)
I have (I think) the KJR Beacon LED with the 30" gooseneck. It has the same base as yours but a much small head.  It has been perfect for my needs but the only hollow forms I've done are segmented.  I think it was about $50 at the time.
"I tried being reasonable..........I didn't like it." Clint Eastwood
Reply
#10
  Re: Seeing the light....inside a bowl by Smashedfinger ([align=left]Ok, I ca...)
I use this one on the back of the grinder and it is great.  The base is 1.5x1.5 and does not slip off the side of the grinder at all.

https://www.amazon.com/gp/product/B07J4Z...UTF8&psc=1


I use this bench light from Menards that sits on top of a file cabinet behind the lathe and I think it is the very best one I have ever had.   I put 6 1" magnets I have and it stays glued to the top of the cabinet and I use a bright 100w led bulb in it.  It bends up and down and the head goes 360* so it will go anywhere I want the light.


https://www.menards.com/main/lighting-ce...259058.htm
It is always the right time, to do the right thing.

Hi, I'm Arlin's proud wife! His brain trma & meds-give memory probs and has pain from injuries, but all is well materially & financially.  
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.