Your Biggest Tool Purchase Mistakes?
#31
A Makita 3 HP plunge router.  I got it in hopes of replacing my Porter Cable 514 2-1/2 HP router that I had to hand plunge into 3/4 birch plywood and cut out a pattern.  The Makita cut about 1/8 of a circle and stalled.  It might suck up 3 HP worth of juice but it doesn't put it down where the bit meets the wood.  To boot, it was flimsy and deflected under load.  Lesson learned.
Reply
#32
Shaper here also...it doesn't get used for what I build.  Got a heck of a deal on it, the space it takes up is no big deal. Still has my footprints on the table from adjusting the clock above it.  
Laugh

Ed
Reply
#33
All things made by Black & Decker
Thanks,  Curt
-----------------
"Life can only be understood backwards; but it must be lived forwards."
      -- Soren Kierkegaard
Reply
#34
(05-11-2020, 08:24 PM)Aram Wrote: Delta X-5 Unisaw. I've told this story too many times here. Death by normal use.
Really?  Why?

Had mine for close to 20 years.  Mine was a made in the USA model, but haven't had a lick of trouble with it.
"This is our chance, this our lives, this is our planet we're standing on. Use your choice, use your voice, you can save our tomorrows now." - eV
Reply
#35
(05-12-2020, 02:37 AM)cputnam Wrote: All things made by Black & Decker

You must not have purchased anything from B&D in the 90's.  Still have my Saw Cat, 3/8 drill and drywall gun and all three are going strong to this day.
"This is our chance, this our lives, this is our planet we're standing on. Use your choice, use your voice, you can save our tomorrows now." - eV
Reply
#36
Jointer which sits in the corner and gathers dust.  I just never use it.  Good thing I bought it used so I don't have a ton of money in it.
Mike


If you're the smartest person in the room, you're in the wrong room!

But not today...
Reply
#37
(05-12-2020, 06:58 AM)KLaz Wrote: Really?  Why?

Had mine for close to 20 years.  Mine was a made in the USA model, but haven't had a lick of trouble with it.


Why? First, Delta. Second, the saw.

I bought the saw new in 2004 (? 2005?). One day,  I stripped the arbor threads -- probably my fault --  but by that time, Delta (in whatever incarnation it was in at the time) didn't stock any parts. A friend with a machine shop turned new threads for me. A few years later, I could barely raise the blade. Disassembly showed that the lift rack teeth were trashed. I took care of the saw, ran DC from a cyclone, kept it clean. No replacement was available, and my top-of-the-line recent-model saw was a giant paperweight.

It was ridiculous. It was a great saw when it ran.

I've been running a mid 80s Powermatic PM66 ever since. Not one problem ever, even though dust removal is worthless, and one might expect more wear on parts.
Best,
Aram, always learning

"Perfection is achieved, not when there is nothing more to add, but when there is nothing left to take away.” Antoine de Saint-Exupery


Web: My woodworking photo site
Reply
#38
(05-11-2020, 08:16 PM)Gary G™ Wrote: Grizzly wet sander. What a POS!
Good thing it was very inexpensive but still a pile!

HA!  I think I bought two or three different wet wheel sharpeners, all were a POS; finally broke down and bought a Tormek which 15 years later is still as good as the day I bought it.
Credo Elvem ipsum etiam vivere
Non impediti ratione cogitationis
Reply
#39
I've a list of small hand (power) tools I shouldn't have bought...maybe even a few accessories. But for big tools, I'd have to say the dumbest thing I did was spending the money to go with 5HP on my Sawstop as opposed to 3 HP. I bought the 5 because I could....which turns out to be a very dumb reason.
I started with absolutely nothing. Now, thanks to years of hard work, careful planning, and perseverance, I find I still have most of it left.
Reply
#40
(05-12-2020, 08:15 AM)Aram Wrote: Why? First, Delta. Second, the saw.

I bought the saw new in 2004 (? 2005?). One day,  I stripped the arbor threads -- probably my fault --  but by that time, Delta (in whatever incarnation it was in at the time) didn't stock any parts. A friend with a machine shop turned new threads for me. A few years later, I could barely raise the blade. Disassembly showed that the lift rack teeth were trashed. I took care of the saw, ran DC from a cyclone, kept it clean. No replacement was available, and my top-of-the-line recent-model saw was a giant paperweight.

It was ridiculous. It was a great saw when it ran.

I've been running a mid 80s Powermatic PM66 ever since. Not one problem ever, even though dust removal is worthless, and one might expect more wear on parts.
Sucks you had bad luck with the Unisaw.  I'm sure that PM66 is a terrific saw though!
"This is our chance, this our lives, this is our planet we're standing on. Use your choice, use your voice, you can save our tomorrows now." - eV
Reply


Forum Jump:


Users browsing this thread: 2 Guest(s)

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.