VGDF Blotchy with stain
#8
I am getting ready to build 3 screen doors for the house. I am using Vertical Grain Douglas fir. I tested staining the fir with an cedar colored oil stain. The color is ok but it is blotchy.
What can I do to even out the color absorb. I am trying to get the VGDF to look some what like cedar. I can not find clear cedar around here and have plenty of the dug fir.
Treat others as you want to be treated.

“You only live once, but if you do it right, once is enough.” — Mae West.
24- year cancer survivor
Reply
#9
I am going by what I've read, not from experience. 

Sanding with fine sandpaper is supposed to help.

I've been interested in trying out Watco Danish oil (available in a reddish color) on pine.  But you will want to know before I get a chance to test that out.

I have had experience with wipe on stains on pine.  You can wipe off more or less depending upon the effect you want.  Make sure you have good light to observe the effect.  It did a nice job on the dark walnut color on  a pine frame.
No animals were injured or killed in the production of this post.
Reply
#10
Trying to stain pine, fir, etc, is nothing but heartache.  And your choice of potential solutions is greatly reduced because these are exterior doors so you can't use interior only rated products.  I'd forget it and either clearcoat or paint them.  

John
Reply
#11
(06-02-2020, 02:11 AM)lift mechanic Wrote: I am getting ready to build 3 screen doors for the house. I am using Vertical Grain Douglas fir. I tested staining the fir with an cedar colored oil stain. The color is ok but it is blotchy.
What can I do to even out the color absorb. I am trying to get the VGDF to look some what like cedar. I can not find clear cedar around here and have plenty of the dug fir.

Minwax wood conditioner or shellac in a spray can before staining.
Reply
#12
I'll try shellac on some scrap and then stain. I have never used shellac, guess it is time to experiment. I like VGDF for it's stability and I have enough for the 3 doors. I am going to Libby, Mt. next week they have a pretty good lumber yard. I'll look for some clear heart cedar.
Treat others as you want to be treated.

“You only live once, but if you do it right, once is enough.” — Mae West.
24- year cancer survivor
Reply
#13
I met Norm Abrams at a hardware show about 25 years ago.  He was at the DeWalt booth.  DeWalt was showing off a new table saw.

Abrams had several of his smaller pieces on display at the booth and he was available to talk to.  Since I was also exhibiting I got to meet him before the show started. 

He had a small "desk" that would sit on a table made from pine.  He said he only used Minwax's Polyshades on pine.  It was the only finish that he found that never caused blotchy appearance.  I've pretty much stuck with that advice and I would agree. 

Notwithstanding  the fact that most "serious" woodworkers look down on Minwax's products (primarily, I suspect because "everyone" uses it), their finishes (especially their oil based poly) is very durable and easy to apply.

I would note that my 22 year old Minwax finished items have a harder finish than one that came right off the line.  It takes 10 days for it to "fully" cure, and for the following year or so it cures beyond "fully". 

But it ends up being very durable.
No animals were injured or killed in the production of this post.
Reply
#14
(06-04-2020, 12:41 AM)lift mechanic Wrote: I'll try shellac on some scrap and then stain. I have never used shellac, guess it is time to experiment.  I like VGDF for it's stability and I have enough for the 3 doors. I am going to Libby, Mt. next week they have a pretty good lumber yard. I'll look for some clear heart cedar.

Libby, MT.  I've been there, back when WR Grace mined vermiculite there.  Beautiful area.  

As for the finish on your doors, keep in mind using interior rated products for an exterior application often leads to problems.  Shellac is a poor choice for anything outside, except for spot priming, even as a sealer.  Minwax Polyshades is an interior only product. 


Take a look at PPG Cetol Window and Door finish.  It comes in several colors, which may be intermixed, too.  It will give you uniform color like Polyshades, but is exterior rated.  I have used it on two exterior doors and it looks great and is very durable.  

John
Reply


Forum Jump:


Users browsing this thread: 2 Guest(s)

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.