Posts: 19
Threads: 0
Joined: Sep 2019
11-25-2020, 01:12 AM
Hi All. Hope you're staying safe wherever you are in the world. Though I know that task is getting harder in some corners of the world at the moment.
I recently finished a small stool made to accompany a dressing table I made about a year ago. It's mostly hand tool work from rough sawn Tasmanian Oak. Stock prepared by hand, joinery work by hand. Router employed for doing the edge chamfers and roughly forming the bum curve in the seat using a curved sled. The roughly formed bum curve was then smoothed with a card scraper which was way more effective that I had anticipated. I hardly had to touch it with sandpaper in the end. The seat floats above the legs about 20mm, or 0.7874 inches
I started this one during our covid isolation (around April/May) then work life got very hectic after isolation and quite a few weekend shop sessions were lost, but finally I got it done and put into service weekend just gone.
What I learned from this build was that there's as much work in a stool as there is a dining table. So if given the choice definitely choose the dining table. But if you need a stool and not a dining table, then you just have to grin and bear it.
Posts: 2,342
Threads: 0
Joined: Dec 2006
Location: virginia beach VA
Nice work. Surprised to hear that there is more work in a stool than a dining table, the last dining table I built took a long time, though a lot of it was deciding how to have the leaves store in the table.
Posts: 850
Threads: 0
Joined: Aug 2014
Wow! That will be good for generations to come!
Thanks for showing!
Chris
Posts: 2,762
Threads: 0
Joined: Dec 2005
Excellent: wedged through tenons really add a nice touch.
Posts: 162
Threads: 1
Joined: Sep 2017
(11-25-2020, 01:12 AM)AlistairD Wrote: Hi All. Hope you're staying safe wherever you are in the world. Though I know that task is getting harder in some corners of the world at the moment.
I recently finished a small stool made to accompany a dressing table I made about a year ago. It's mostly hand tool work from rough sawn Tasmanian Oak. Stock prepared by hand, joinery work by hand. Router employed for doing the edge chamfers and roughly forming the bum curve in the seat using a curved sled. The roughly formed bum curve was then smoothed with a card scraper which was way more effective that I had anticipated. I hardly had to touch it with sandpaper in the end. The seat floats above the legs about 20mm, or 0.7874 inches
I started this one during our covid isolation (around April/May) then work life got very hectic after isolation and quite a few weekend shop sessions were lost, but finally I got it done and put into service weekend just gone.
What I learned from this build was that there's as much work in a stool as there is a dining table. So if given the choice definitely choose the dining table. But if you need a stool and not a dining table, then you just have to grin and bear it.
Looks like a very comfortable stool
Posts: 6,678
Threads: 1
Joined: Jan 2003
Location: Southern California
Nice clean lines and a well shaped seat. I like it!
Thanks, Curt
-----------------
"Life can only be understood backwards; but it must be lived forwards."
-- Soren Kierkegaard
Posts: 4,815
Threads: 1
Joined: Jan 2004
Location: Eugene, OR
(11-25-2020, 01:12 AM)AlistairD Wrote: Hi All. Hope you're staying safe wherever you are in the world. Though I know that task is getting harder in some corners of the world at the moment.
I recently finished a small stool made to accompany a dressing table I made about a year ago. It's mostly hand tool work from rough sawn Tasmanian Oak. Stock prepared by hand, joinery work by hand. Router employed for doing the edge chamfers and roughly forming the bum curve in the seat using a curved sled. The roughly formed bum curve was then smoothed with a card scraper which was way more effective that I had anticipated. I hardly had to touch it with sandpaper in the end. The seat floats above the legs about 20mm, or 0.7874 inches
I started this one during our covid isolation (around April/May) then work life got very hectic after isolation and quite a few weekend shop sessions were lost, but finally I got it done and put into service weekend just gone.
What I learned from this build was that there's as much work in a stool as there is a dining table. So if given the choice definitely choose the dining table. But if you need a stool and not a dining table, then you just have to grin and bear it.
Nice done! Love the wedged through tenons.
Best,
Aram, always learning
"Perfection is achieved, not when there is nothing more to add, but when there is nothing left to take away.” Antoine de Saint-Exupery
Web:
My woodworking photo site
Posts: 19
Threads: 0
Joined: Sep 2019
barryvabeach, cheers! oh yeah i could imagine an extending table would add a little complexity to the task
C. in Indy, thanks! It's a nice feeling to think I can make something that will outlast me.
Philip1231, agree. I love the look and the strength. I have the compulsion to put them everywhere I can.
Woodworm! yes function won out over form. I originally intended to keep the edges of the seat squarer but it wasn't as comfortable.
cputnam, thanks! i had planned to prototype it in pine to see if i liked the proportions but in the end after drawing it out at 1:1 scale I just jumped in to the final build and feel like it worked out ok.
Aram. cheers! not the quickest joinery method but every time i assemble a wedged through tenon its such a feeling of accomplishment
