Lateral support for 6x6 post in sadle bracket
#6
Hello
I am mounting 2 posts 6x6 in sadle brackets that are set in concrete. The 2 post are at the side of the patio furthest from the house.  I want to avoid a support between the 2 posts.  I want to run a 2x4 on either side of the top of each post back to the lam beam attached to the house. There will be a a sunshade attached at the top 4 corners. We don't want a support between the two posts because it will be blocking the view of the sunset. The railing attached to the posts will be 3ft tall.  The attached pics should help. 
My question is if this looks like the posts are well supported without a top brace between them.


Attached Files Image(s)
   
   
   
Reply
#7
No.   without a diagonal brace you would need to cantilever the forces into the ground somehow.  This could be done by burying the post in concrete many feet deep.  Or, using a strap anchor on all four sides that extend up the post a foot or more.  The saddle bracket you show will let them wiggle too much.   What about a crossbrace between the two post up high and then diagonals out of 1/4" black cable?  That would make a rigid end assembly.

a second possbility would be to use the roof plane as a shear diaphram.  Run 4x4s from the house LVL to the top of the 6x6 and then also between the 6x6's. Then, add the x brace cabling in this horizontal assembly.  This would use your house to brace the new roof and thus keep the 6x6's from moving sideways.
WoodNET... the new safespace
Reply
#8
We had a similar problem when I was building a 16' x 16' pergola. I also used 6" x 6" x 10' cedar posts on saddle brackets. I was worried with the large sway once the posts were installed and was worried I would have to tie-in the structure to the house. I used double 2 x 6's parallel to the house and 2 x 6's perpendicular to those. I also added double 2 x 6 angle brackets on all the posts. For the roof I used 1 x 2's for shade. Once all the structure is on, there is zero sway and there was no need to brace against the house. Hope this helps.
Gilbert


Attached Files Image(s)
   
   
   
Reply
#9
(06-04-2021, 02:32 AM)00lightning Wrote: We had a similar problem when I was building a 16' x 16' pergola.  I also used 6" x 6" x 10' cedar posts on saddle brackets.  I was worried with the large sway once the posts were installed and was worried I would have to tie-in the structure  to the house.  I used double 2 x 6's parallel  to the house and 2 x 6's perpendicular  to those.  I also added double 2 x 6 angle brackets on all the posts.  For the roof I used 1 x 2's for shade.  Once all the structure  is on, there is zero sway and there was no need to brace against the house.  Hope this helps.
Gilbert

Looks great. Those V braces at the top of the posts are controlling most if not all of the sway.    Roly
Reply
#10
I have no experience with these, but I've seen them used just as you have described.  A complete kit with four corner posts and four base mounts is $360.00.  Not cheap, but it is a very clean installation.

https://tojagrid.com/products/trio-3-arm...gL2U_D_BwE

[Image: trio6.png?v=1593510818]
No animals were injured or killed in the production of this post.
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.