Work bench thickness is 3" too much?
#21
My split top roubo is 4 inches thick
"Oh. Um, l-- look, i-- i-- if we built this large wooden badger" ~ Sir Bedevere
Reply
#22
If you can save lumber cost by going thinner, go with a 2" top. I use holdfasts and do lots of handplaning, and the 2" top presents no issues whatsoever. But don't intentionally go for a thinner top if it won't save you any money.

The thinnest top I had used is 1-3/4" for a decade, and it too gave me no problem either.

Simon
Reply
#23
Do 6" of the surface 3" thick for the holddown holes, then the rest of the top, say 24", do it 2" thick.
Make the skirt around the edges all the same.
Steve

Mo.



I miss the days of using my dinghy with a girlfriend too. Zack Butler-4/18/24


 
The Revos apparently are designed to clamp railroad ties and pull together horrifically prepared joints
WaterlooMark 02/9/2020








Reply
#24
I’ve made a lot of good furniture on a 1-1/2” thk doug fir workbench. I’d be more concerned about how easy it will be clamp stuff to the top. Next question is if you can clamp a long board to the front for edge work.

Qualifier: my bench is a Nicholson style bench with deep aprons that stiffen the otherwise thin top. When mallet work or mortising is reqd, I work over one of the legs.
Reply
#25
(10-14-2021, 04:14 AM)iclark Wrote: If you are starting with "nominally" 4" wide maple boards, then winding up with a benchtop that is around 3" thick after you flatten both sides is quite reasonable. 3" thick is a good thickness for a hand tool bench top.

When picking boards, you want to use ones that are closer to flat-sawn than quarter-swan. That way, your glued-up top will be close to quarter-sawn. That helps minimize problems from seasonal moisture changes.

My boards are already onhand.  They have been acclimatizing in the home for about 20 years.  I think a few boards were put to use by some tenants when I rented the home out.  So now I would have to buy only a few more boards to make the bench at 3".  I have made a sled to flatten the boards on my planer so I can inventory the total useable feet I have available.

Once I do this I can determine how many board feet I would need to buy to make it to plans which is 3" thick.  If I do need more lumber the nearest hardwood source is 2 hours away.  One of the problems then is I need to acclimate the boards in the garage.


Attached Files Image(s)
   
A carpenter's house is never done.
Reply
#26
(10-16-2021, 09:51 PM)photobug Wrote: They have been acclimatizing in the home for about 20 years.

Translation - Lumber sitting idle and not used for some 20 years!
Laugh
Winkgrin

Simon
Reply
#27
(10-17-2021, 09:25 AM)Handplanesandmore Wrote: Translation - Lumber sitting idle and not used for some 20 years!
Laugh
Winkgrin

Simon

In my defense, I was absent for 17 of those years.

But what I want to know, do you think the wood is ready to be worked yet.
Big Grin
A carpenter's house is never done.
Reply
#28
(10-17-2021, 11:07 AM)photobug Wrote: In my defense, I was absent for 17 of those years.

But what I want to know, do you think the wood is ready to be worked yet.
Big Grin

Less critical is the no. of years of acclimatization in the home but how different the humidity conditions between your home and shop are. If the home is humidity controlled while the shop is not, I'd place lumber in the shop first, perhaps for a few weeks.

Simon
Reply
#29
(10-17-2021, 12:35 PM)Handplanesandmore Wrote: Less critical is the no. of years of acclimatization in the home but how different the humidity conditions between your home and shop are. If the home is humidity controlled while the shop is not, I'd place lumber in the shop first, perhaps for a few weeks.

Simon

I did not even think about it but the wood has spent the last few years in the crawl space and have been back in the shop for a few weeks now.  The home and shop get heated in winter, other than that no climate controlled.  I just looked up Wyoming and it is the 3rd lowest relative humidity state behind Utah and Arizona.   I would think garage, shop, and crawlspace are all the same humidity, the shop is the garage.
A carpenter's house is never done.
Reply
#30
That wood should be good to work on, if so.

I have had a few occasions on which some boards (cherry or mahogany, 1" to 2" thick) twisted slightly on me after I put them in the shop (attached garage). Walnut seems to be better.

Simon
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.