Making some knives
#7
It’s my daughter’s boyfriend’s birthday tomorrow, and I decided to make him a set of crook knives. They’ll be here in a week, so I have a little time.
Wink While I was at it, I decided to make myself a knife as well.

The steel is O1, 1/8” thick for the crook knives, 7/64” thick for mine. A few hours with a hacksaw and files, and removed file marks with a sharpening stone. I didn’t have a good form for bending the crook knives, but they didn’t turn out too bad.

Ready for heat treating!

Ok…struggling with photos…hopefully I’ll get that figured out soon.
Dave Arbuckle was kind enough to create a Sketchup model of my WorkMate benchtop: http://www.arbolloco.com/sketchup/MauleSkinnerBenchtop.skp
Reply
#8
Well, photo uploading is eluding me. Never mind, I guess.
Dave Arbuckle was kind enough to create a Sketchup model of my WorkMate benchtop: http://www.arbolloco.com/sketchup/MauleSkinnerBenchtop.skp
Reply
#9
(04-02-2022, 06:32 PM)MauleSkinner Wrote: Well, photo uploading is eluding me. Never mind, I guess.

I can upload them for you, if you like. PM incoming
Best,
Aram, always learning

"Perfection is achieved, not when there is nothing more to add, but when there is nothing left to take away.” Antoine de Saint-Exupery


Web: My woodworking photo site
Reply
#10
Here you go
[Image: i-BHtT3t6.jpg]
Best,
Aram, always learning

"Perfection is achieved, not when there is nothing more to add, but when there is nothing left to take away.” Antoine de Saint-Exupery


Web: My woodworking photo site
Reply
#11
Thanks, Aram!

Obviously the bottom two are the crook knives. I plan to make the handles in two pieces for those, with a mortise in one side and then glued together.

For my knife, I decided to try through-drilling the handle for the tapered tang, and peening the end of the tang to help secure it. The goal is something similar to a Mora 122 to complement my 120 that I use for whittling.
Dave Arbuckle was kind enough to create a Sketchup model of my WorkMate benchtop: http://www.arbolloco.com/sketchup/MauleSkinnerBenchtop.skp
Reply
#12
Heat treating today…

No serenade,
No fire brigade,
Just pyromania!
Big Grin

A local store had the “one log fire” on clearance, so I decided to give that a try. Light the center, and used my leaf blower to force air to get it good and hot. I used a locking pliers to hang the blades into the fire. By the time it burned the center hole big enough for the crook blades to fit, it had also burned through a split in the other side…you can see by he one picture that he log burned through on the bottom because of the blower. I had to hold both the blower and the steel in just the right place to get it to work. Didn’t work out as well as I hoped, but it still worked.

Quenched in peanut oil and wiped off, next I’ll scrub them with a scotch rite pad and temper them in a toaster oven.

Aram will hopefully have the pics up soon.

Thanks for looking!
Dave Arbuckle was kind enough to create a Sketchup model of my WorkMate benchtop: http://www.arbolloco.com/sketchup/MauleSkinnerBenchtop.skp
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.