|
NEW WIP
|
06-06-2022, 02:02 PM
Jack Of All Master Of None
https://www.facebook.com/serenityartisans/ My 16' Cedar Canoe build http://www.clcboats.com/forum/clcforum/t...28426.html 
Interesting start.
I look forward to seeing progress.
"the most important safety feature on any tool is the one between your ears." - Ken Vick
A wish for you all: May you keep buying green bananas.
06-10-2022, 03:31 PM
Okay everyone the progress continues on my new WIP. I'm just about done carving out the first side. You can see in the photos some of the hand tools being used to carve the tear drops to a point. The first step is to make ta hole using a Dremel and a rotary cutter, then the Flexcut knife to cut the point. You will also see the layout of side two. This is just the start of the first section of several parts. This Teak cylinder is 4 1/2" x 9 1/2" 1/8" thick wall.
Jack Of All Master Of None
https://www.facebook.com/serenityartisans/ My 16' Cedar Canoe build http://www.clcboats.com/forum/clcforum/t...28426.html 
06-10-2022, 06:41 PM
I have little experience with teak and cannot imagine carving it. You have done other projects with teak, so clearly, you have no problems with the wood.
Looking forward to seeing the next stages.
"I tried being reasonable..........I didn't like it." Clint Eastwood
06-12-2022, 01:02 PM
(06-10-2022, 06:41 PM)Bill Holt Wrote: I have little experience with teak and cannot imagine carving it. You have done other projects with teak, so clearly, you have no problems with the wood. Bill it carves very well and sands even better, I'll be sure to post the next phases photos here.
Jack Of All Master Of None
https://www.facebook.com/serenityartisans/ My 16' Cedar Canoe build http://www.clcboats.com/forum/clcforum/t...28426.html
06-18-2022, 11:06 AM
(This post was last modified: 06-18-2022, 11:06 AM by Splinterz25.)
Lots of holes !! The precision carving continues, I have pierced almost all of the holes in this first section of the project. Now I have to hand carve the rest of the tear drop away with knives and clean them all up smooth.
Jack Of All Master Of None
https://www.facebook.com/serenityartisans/ My 16' Cedar Canoe build http://www.clcboats.com/forum/clcforum/t...28426.html
06-18-2022, 02:49 PM
It is a cool looking piece so far.
"I tried being reasonable..........I didn't like it." Clint Eastwood
06-20-2022, 08:48 AM
(06-18-2022, 02:49 PM)Bill Holt Wrote: It is a cool looking piece so far. Thank you Bill, In the next phase I will be cutting the cylinder apart into two pieces, the cut lines are already drawn on the piece.
Jack Of All Master Of None
https://www.facebook.com/serenityartisans/ My 16' Cedar Canoe build http://www.clcboats.com/forum/clcforum/t...28426.html
06-22-2022, 02:45 PM
(This post was last modified: 06-22-2022, 02:46 PM by Splinterz25.)
My WIP continues to evolve: I have finished cutting the vast majority of the tear drop holes and have cleaned them up some what, more fine tuning yet to come. Then I have sliced the whole cylinder in half and cleaned it a bit as well. I have photos of me carving the V section of the teardrop and cutting the piece apart if anyone wants to see that let me know.
Jack Of All Master Of None
https://www.facebook.com/serenityartisans/ My 16' Cedar Canoe build http://www.clcboats.com/forum/clcforum/t...28426.html |
|
|
Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.
