Lathe Problem
#11
I have a problem with the tail stock on my Delta 1440 lathe.  I got the lathe for free from my brother several months ago and it has worked flawlessly up until a couple of weeks ago.  A couple of weeks ago, the wheel crank on the tailstock started getting harder to turn.  I was drilling yesterday and pushing the drill bit in with the wheel crank on tail stock, and it got quickly and progressively got harder to turn to the point where it nearly seized up.  I took it all apart, cleaned and lubricated the spindle screw, the quill, the lock, and the cylinder of the tail stock.  Put it back together and same problem to the point where I couldn't even use the wheel crank to pull the spindle screw and pull out of the tail stock; I had to use channel locks with an enormous amount of force to get the two of them separated.  I cleaned everything again today, and I can get the spindle screw in only about a half of an inch, rather than the six inches it should screw into.  

I am new to woodturning but this seems like a weird problem to me.  I thought maybe the spindle screw and/or the quill became stripped, but I see wear and tear on the threads, but no damage.  I am stumped so any suggestions would be appreciated.  I have "caught the bug" so I will have to shop for a new lathe if there is not a solution.  I have not been able to find parts anywhere on the internet for these old Delta lathes.  Thank you as always...
Reply
#12
First check the turn lock at the top or side of the quill it might have been turned to tight, if that is not the problem then take it apart and clean and lube it.
As of this time I am not teaching vets to turn. Also please do not send any items to me without prior notification.  Thank You Everyone.

It is always the right time, to do the right thing.
Reply
#13
Thanks for the reply, Arlin.  I have done all that already (did before I posted on here yesterday).  I am stumped.  

Since everything else seems to be fine, I am wondering if I can get another quill and spindle screw that will fit the Delta tail stock.  I hate to think the machine is done due to the tailstock problem.  Thanks again.
Reply
#14
Seems like it has to be damaged threads on the spindle screw or damaged locking mechanism on the quill if it's that tight. Can you post a picture of the parts when it's disassembled?
Reply
#15
(09-19-2022, 01:21 PM)FrankAtl Wrote: Seems like it has to be damaged threads on the spindle screw or damaged locking mechanism on the quill if it's that tight. Can you post a picture of the parts when it's disassembled?

When my tailstock quill was too tight, I discovered that the handle was held onto the quill screw with 2 setscrews and was jammed into the body. When I took everything apart, the screw easily threaded into the quill when not in the tailstock body. Putting it back together with a little lash between the handle and body fixed it.

I would check:
1. Does the quill slide easily in the body with the screw removed?
2. Does the screw turn easily in the quill without the body?
We do segmented turning, not because it is easy, but because it is hard.
Reply
#16
(09-19-2022, 08:29 PM)SceneryMaker Wrote: When my tailstock quill was too tight, I discovered that the handle was held onto the quill screw with 2 setscrews and was jammed into the body.  When I took everything apart, the screw easily threaded into the quill when not in the tailstock body.  Putting it back together with a little lash between the handle and body fixed it.

I would check:
1.  Does the quill slide easily in the body with the screw removed?
2. Does the screw turn easily in the quill without the body?
Thanks for you responses.  The quill slides fairly easily in the body without the spindle screw.  When outside the tailstock housing, the spindle screw will only screw into the quill about a half inch (instead of about 5") and then gets so tight, it can't be turned.  It must be damaged threads, but they don't look damaged at all.  I just can't figure out what else it could be.
Reply
#17
(09-20-2022, 05:41 AM)fptahoe Wrote: It must be damaged threads, but they don't look damaged at all.  I just can't figure out what else it could be.

Hold a straightedge against the threads. That will tell you if it is bent. Did you tighten the tailstock really tight?
Reply
#18
(09-20-2022, 09:06 AM)hairy Wrote: Hold a straightedge against the threads. That will tell you if it is bent. Did you tighten the tailstock really tight?

I did that a while back on one of the mini lathes and tried reallllllllly hard to screw it out.  After taking it out I ended up putting it between centers and sanding it out.  Then had to sand the inside that has a big scratch in the metal from the quill.   
Slap
As of this time I am not teaching vets to turn. Also please do not send any items to me without prior notification.  Thank You Everyone.

It is always the right time, to do the right thing.
Reply
#19
(09-19-2022, 01:21 PM)FrankAtl Wrote: Seems like it has to be damaged threads on the spindle screw or damaged locking mechanism on the quill if it's that tight. Can you post a picture of the parts when it's disassembled?

Sounds like it. If the OP can figure out which is damaged, might be solvable with running a tap or a die to clean up the threads.

Assuming it’s not just sawdust and grease packing the ram.

-Mark
If I had a signature, this wouldn't be it.
Reply
#20
(09-20-2022, 05:41 AM)fptahoe Wrote: Thanks for you responses.  The quill slides fairly easily in the body without the spindle screw.  When outside the tailstock housing, the spindle screw will only screw into the quill about a half inch (instead of about 5") and then gets so tight, it can't be turned.  It must be damaged threads, but they don't look damaged at all.  I just can't figure out what else it could be.

maybe the internal threading is boogered up a bit?  
Confused
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.