In need of a replacement
#31
Fella, you make it look so easy!
"I tried being reasonable..........I didn't like it." Clint Eastwood
Reply
#32
Grooves are needed to house the plywood panels for the drawer bottoms...fastest way I know?
   
Stanley No. 45 with a 1/4" wide cutter ( that I also just sharpened back up)
   
Fence is set so that the groove is 1/4" above the bottom edge of the sides/front..
   
Sharp cutter vs a knot....sliced right on through..
   
The pine sides...made a lot of long curls...the Ash fronts?   A LOT of chips..
   

There was one drawer side mis-marked..and that is how it got a groove along the top edge and the bottom edge..as I was NOT about to make a replacement..

I had thought about setting up the "other" Stanley #45..
   
But...trying to jig up a way to mill dados with it....and since I will need to use the tablesaw for other items...decided to just mill the dados on the saw...and clean them up with a chisel...
   
The other operations?   Was to cut 4 drawer backs to length ( avoiding the bigger knots) and then rip to height ( removing those bigger knots), then have it set up to cut a drawer bottom panel to size..
   
Enough for 3 drawers?   Where is the stuff for the 4th drawer?
   
Sitting in the clamps, of course...
   
Checked for square, before the screws were installed. 

Stay tuned...stil have 3 more drawers to build....
Show me a picture, I'll build a project from that
Reply
#33
No. 2....
   
No. 3..
   
and No. 4
   

Looks like I will be spending today, cleaning these 4 up..so they will slide into the case easily...and see about some knobs getting installed...so I can pull the drawers back out...maybe think about a finish for this Project....

Stay tuned..
Winkgrin
Show me a picture, I'll build a project from that
Reply
#34
Drawers have been cleaned up, and handled...and fitted to the case..
   
A plug was cut....
   
Installed, trimmed flush with a block plane.

A "blend" of  Amber Shellac and Witch's Brew stain has been brushed on...
   
Awaiting a coat of Clear Gloss Poly this afternoon...
   
Might move this upstairs tomorrow....as the Boss wants to see it...
   
Not too bad of a little Project?
Show me a picture, I'll build a project from that
Reply
#35
I like it.  Nice work.
Reply
#36
As always Bandit, you keep designing and building at a rapid pace. All the while photographing
the project and procedures and then posting here. You put the majority of us here to shame. At
least as far as actual woodworking content for this site. It IS noticed and appreciated.

I am certain there are plenty of woodworkers here who are just as busy. But you take it
to the next level. It is no small thing to take the time to document the process and then post it for
all of us to see.

So, short version, Thank You!!
Mark Singleton

Bene vivendo est optimum vindictae


The Laws of Physics do not care about your Politics   -  Me
Reply
#37
Mark said it very well.

Thank you for taking us along.
"I tried being reasonable..........I didn't like it." Clint Eastwood
Reply
#38
I agree. THanks for the build along.

Why did you combine the amber shellac with the stain? It looks very nice, BTW.
Reply
#39
Blend was because I did not have enough of either....
Show me a picture, I'll build a project from that
Reply
#40
As always Bandit, we'll done sir.
Happy to know Chester now has a place for his drawers. ;=)
If you continue to cut corners, you'll end up going in circles!

It's my thumb so I'll hit it if I want to!
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.