+- Woodnet Forums (https://forums.woodnet.net)
+-- Thread: Ye olde MM16 power switch post [NEW QUESTION ADDED] (/showthread.php?tid=7352882)
Pages:
1
2
Ye olde MM16 power switch post [NEW QUESTION ADDED] - Aram - 02-11-2020
My 2004 Minimax MM16 stopped working yesterday. I need to confirm that it is the startup switch, and not the door interlock. I confirmed 220V AC at the switch.
Assuming it's the switch, I have a couple of questions. One, I replaced the switch once already (before the SCM days). A Minimax rep posted a very helpful replacement procedure on the Minimax Yahoo user group. It saved a lot of guessing and hassle. That group is no more and I don't seem to have a copy of the steps. Does anyone know or remember what order to disconnect, remove etc? There is definitely a smart way.
Two, the switch is AEG 910-201-211. I bought my last one from Minimax. I've had poor experience with SCM and I'd rather buy it somewhere else. Any recommendations? I see a huge amount of online pricing variations, which makes me suspicious.
Thanks. I'll check the interlocks tonight.
[EDIT] Does anyone know the spec for the door and brake microswitches (interlocks) in case that's the problem?
RE: Ye olde MM16 power switch post - Banditt - 02-11-2020
I've had switch problems myself a couple of times but fortunately a tap or two with the back of a screwdriver and a blast of air has got me going again. I've bookmarked the following for the day I'm not so lucky, hope it helps.
http://www.solowoodworker.com/mm/switch.html
RE: Ye olde MM16 power switch post - jteneyck - 02-11-2020
(02-11-2020, 12:03 PM)Aram Wrote: My 2004 Minimax MM16 stopped working yesterday. I need to confirm that it is the startup switch, and not the door interlock. I confirmed 220V AC at the switch.
Assuming it's the switch, I have a couple of questions. One, I replaced the switch once already (before the SCM days). A Minimax rep posted a very helpful replacement procedure on the Minimax Yahoo user group. It saved a lot of guessing and hassle. That group is no more and I don't seem to have a copy of the steps. Does anyone know or remember what order to disconnect, remove etc? There is definitely a smart way.
Two, the switch is AEG 910-201-211. I bought my last one from Minimax. I've had poor experience with SCM and I'd rather buy it somewhere else. Any recommendations? I see a huge amount of online pricing variations, which makes me suspicious.
Thanks. I'll check the interlocks tonight.
That looks like the same starter switch I had to replace for a too small one on my MM FS-35 J/P. There's not much to it. Take out the old, connect the wires to the same terminals on the new one. Done. I picked someone that looked like a real business online selling it for the lowest price, around $75 IIRC. Turned out fine.
John
RE: Ye olde MM16 power switch post - fredhargis - 02-11-2020
Aram, that switch may have changed part numbers. I found this:"The old switch has AEG Part Nbr 910-201-211 and says "16..20A" and the dial was set at 20A.The new switch has AEG P/N 910-201-212 and says "20..25A" over at SMC (buried down in this thread). I can't help...Charlie Plesums detailed some stuff on the MM switch at his website, but it was on an MM24 and his switch is different than ours. I'm folowing with interest since I have the same saw. I didn't realize that SCM had shutdown the MM site.
RE: Ye olde MM16 power switch post - jteneyck - 02-11-2020
(02-11-2020, 12:22 PM)fredhargis Wrote: Aram, that switch may have changed part numbers. I found this:"The old switch has AEG Part Nbr 910-201-211 and says "16..20A" and the dial was set at 20A.The new switch has AEG P/N 910-201-212 and says "20..25A" over at SMC (buried down in this thread). I can't help...Charlie Plesums detailed some stuff on the MM switch at his website, but it was on an MM24 and his switch is different than ours. I'm folowing with interest since I have the same saw. I didn't realize that SCM had shutdown the MM site.
The smart thing to do is to look at the motor for the FLA (Full Load Amps). My FS-35 pulls something like 16.8 amps but had a 10-15 amp. switch on it, set at 15 amps. Of course it tripped out every time I put much load on it. I replaced it with one with the 16 - 20 amp rating, set it at 17, and all is well.
John
RE: Ye olde MM16 power switch post - Stwood_ - 02-11-2020
My 16 is a 2005-6, I think. It came factory damaged, dealer rebuilt.
Knock on wood, I've never had a switch problem.
If I ever have major problems procuring a switch if mine gives trouble, I'll probably be looking at installing a 220V high amp wall switch, like I did on my Jet 6x89 sander.
RE: Ye olde MM16 power switch post - jteneyck - 02-11-2020
(02-11-2020, 03:03 PM)Stwood_ Wrote: My 16 is a 2005-6, I think. It came factory damaged, dealer rebuilt.
Knock on wood, I've never had a switch problem.
If I ever have major problems procuring a switch if mine gives trouble, I'll probably be looking at installing a 220V high amp wall switch, like I did on my Jet 6x89 sander.
That won't give you any protection unless the breaker is appropriately sized. The motor on my FS-35 has no thermal overload protection; it's provided by the switch. I have the machine plugged into a 30 amp circuit shared with my 5 hp bandsaw so it needs that switch to provide protection.
John
RE: Ye olde MM16 power switch post - Stwood_ - 02-11-2020
(02-11-2020, 03:43 PM)jteneyck Wrote: That won't give you any protection unless the breaker is appropriately sized. The motor on my FS-35 has no thermal overload protection; it's provided by the switch. I have the machine plugged into a 30 amp circuit shared with my 5 hp bandsaw so it needs that switch to provide protection.
John
I have a 220 20amp breaker on that run. Used for the bandsaw and my 6x89 sander.
It's a 3.4? 3.6? hp (hafta look again) motor. It should break a 20 amp breaker.
RE: Ye olde MM16 power switch post - fredhargis - 02-11-2020
It might trip a 20 amp if really pushed, but i ran mine (they are 3.6 HP) on a 20 amp for a few years before and never tripped it. They are rated for a 30 amp breaker (the older ones like ours, the newer ones have a 4.8 HP motor).
RE: Ye olde MM16 power switch post [NEW QUESTION ADDED] - Bob10 - 02-12-2020
I know for furnaces I have installed I have used switches with a fuse in them to protect the machinery
Not sure if you can find something like this for your application but thought I would toss it out there as it might be easier to find than
an exact replacement for a specific machine
![[Image: Z_-6s0fo5oy.JPG]](https://www.zoro.com/static/cms/product/large/Z_-6s0fo5oy.JPG)