+- Woodnet Forums (https://forums.woodnet.net)
+-- Thread: Replace just the plastic piece on stop button? Jointer (/showthread.php?tid=7357494)
RE: Replace just the plastic piece on stop button? Jointer - TDKPE - 08-30-2020
(08-30-2020, 10:42 AM)BpB123 Wrote: If you like the dowel idea but are concerned with the light.... can you find some pvc pipe or other tubing that would work? If a little smaller, some tape on the outside of the tube could solve diameter deltas
Just a thought
Or chuck it up and turn it to the precise diameter you need, since it'll just be a short length. Either/or.
RE: Replace just the plastic piece on stop button? Jointer - Bill Holt - 08-30-2020
No help here. But I am amazed and grateful for the "Woodnet Brain Trust", there is seldom a shortage of ideas for any question.
RE: Replace just the plastic piece on stop button? Jointer - themoon - 08-30-2020
I need a "like" button on here.
RE: Replace just the plastic piece on stop button? Jointer - themoon - 08-30-2020
If I go the wood dowel route.... There's no chance this thing would be at risk of fire, is there? All those wires running through it
RE: Replace just the plastic piece on stop button? Jointer - fredhargis - 08-30-2020
(08-30-2020, 03:01 PM)themoon Wrote: If I go the wood dowel route.... There's no chance this thing would be at risk of fire, is there? All those wires running through it
That switch itself is isolated from the circuitry, besides....plastic also burns.
RE: Replace just the plastic piece on stop button? Jointer - Stwood_ - 08-30-2020
(08-30-2020, 02:54 PM)themoon Wrote: I need a "like" button on here.
Awww. I wish we did.
(08-30-2020, 03:01 PM)themoon Wrote: If I go the wood dowel route.... There's no chance this thing would be at risk of fire, is there? All those wires running through it
Naw. Put the hotdogs away.
RE: Replace just the plastic piece on stop button? Jointer - Phil Thien - 08-30-2020
Where it broke seems like it would break again, so I vote for turning your own thicker piece of plastic, if possible.
RE: Replace just the plastic piece on stop button? Jointer - BrokenOlMarine - 08-31-2020
Don't rag on the OP because he will try and save a buck or two. When we got married, Tina and I had both been raised in families who did the same. It is in your nature. There is a difference between repairing something if you can, because you can, rather than replacing; and being too cheap to buy a new part.
I was also taught, buy quality, buy once.
Buy cheap, buy often.A couple years ago, I had posted a query on the forum about wheels for the castors on one of my power tools. "Buy new castors" was the general consensus. The old black tired wheels were beginning to crumble and break apart. Hey, they were over ten years old.
I kept looking, and found that woodcraft had the wheels in a couple sizes. Just in time, I now needed TWO sets. They had the higher quality red wheels, and they came in three days after I ordered them. I replaced just the wheels, at 1/4 the cost of new castors. When we are talking eight, then another eight the next year, it adds up. Those wheels are still rolling.
RE: Replace just the plastic piece on stop button? Jointer - Timberwolf - 08-31-2020
(08-31-2020, 05:23 AM)BrokenOlMarine Wrote: Don't rag on the OP because he will try and save a buck or two. When we got married, Tina and I had both been raised in families who did the same. It is in your nature. There is a difference between repairing something if you can, because you can, rather than replacing; and being too cheap to buy a new part.................................
I was also taught, buy quality, buy once.
A couple years ago, I had posted a query on the forum about wheels for the castors on one of my power tools. "Buy new castors" was the general consensus. The old black tired wheels were beginning to crumble and break apart. Hey, they were over ten years old.
I kept looking, and found that woodcraft had the wheels in a couple sizes. Just in time, I now needed TWO sets. They had the higher quality red wheels, and they came in three days after I ordered them. I replaced just the wheels, at 1/4 the cost of new castors. When we are talking eight, then another eight the next year, it adds up. Those wheels are still rolling.
LIL
Thirty bucks will buy a few Big Macs...Anybody with the money can buy a new one but not everybody can fix the old one...fix it...then buy some Big Macs...... :nothing wrong with saving money if you can......
RE: Replace just the plastic piece on stop button? Jointer - themoon - 08-31-2020
Thanks for that but it's ok. I don't think they were being that bad, but yes my current predicament in these times is to pinch every cent. This Covid thing has killed our market and finding work is a bi$@!.
Thanks again for everyone that replied with ideas. Tried the dowel idea but the switch had some kind of lip with bracketed holes at the end. Becoming too hard for my talents. Lol guess I'm going to have to save up by not buying all those big mac's.