+- Woodnet Forums (https://forums.woodnet.net)
+-- Thread: Metal Lathe loading challenge (/showthread.php?tid=7319767)
Metal Lathe loading challenge - BloomingtonMike - 07-16-2016
Found a cnc lathe deal and want to go get it since my last one got damaged in greight shipping. So soon I need to make a 650 mile trip to pickup a Birmingham 1236 metal lathe. It has been mechanically converted to CNC so it weighs slightly less than a full gear head lathe but still ~1000lbs. I want to put it in the bed of my Nissan Titan King cab (think extended cab).
My challenge - The place I am buying it from does not have a roll up door at ground height - only semi docks.
My plan is to haul the lathe off the stand on a pallet in the bed of my truck.
So my choices are
1. Roll it out a front pedestrian door and load it in my truck but without the use of their fudge truck
2. Lower it off the dock into the bed of my truck with straps and a fudge truck.
Any advice on how to load it safely in either of the two methods above?
Third option is to pay for freight but I am dealing with a freight damaged latheh right now and really do not want to risk another deal.
They look like this:
Re: Metal Lathe loading challenge - JDuke - 07-16-2016
I used an engine hoist to lift a very similar non CNC lathe into the back of a Honda Ridgeline
Manual should have at least one picture showing where to put straps near headstock
Duke
Re: Metal Lathe loading challenge - Robert Adams - 07-16-2016
Forklift and straps is how I'd go. It's not that heavy so a regular strap will do fine. If I had a few helpers I'd just carry it. That's how we did the ones for the school shop.
Re: Metal Lathe loading challenge - daddo - 07-16-2016
My question is;
What are you going to do when you get it home?
Without my friends bobcat, I would have been stuck.
Re: Metal Lathe loading challenge - Wild Turkey - 07-16-2016
I'd go with the fudge lift and straps, but one question -- are the forks long enough to put the lathe where you need it in the bed? How long is the lathe?
Will it make the truck tail-heavy? Can your tires take the load?
I'd make sure the heavy end of that lathe went forward.
I'm also jealous
Re: Metal Lathe loading challenge - MKepke - 07-16-2016
If you are going to separate the lathe from the stand and palletize the lathe, either method would work.
You shouldn't have much trouble dragging the palletized lathe up a ramp if you cover the ramp with a cheap sheet of 1/4" hardboard (slick side up obviously) and use a comealong.
Works for loading and unloading. But have help..one person to run the comealong, one person to watch & guide the ascent/descent.
-Mark
Re: Metal Lathe loading challenge - Cecil - 07-17-2016
Find someone with a lift gate who is hauling from the same facility. Pay them a few buck to pull away from the dock and lower the load, transfer from truck to truck. It may cost a bit, not it will not be a freight charge.
Re: Metal Lathe loading challenge - BloomingtonMike - 07-17-2016
Man these are all great ideas. Thank you.
I have a tractor with a loader to unload it when I get home.
Re: Metal Lathe loading challenge - daddo - 07-17-2016
Cecil said:
Find someone with a lift gate who is hauling from the same facility. Pay them a few buck to pull away from the dock and lower the load, transfer from truck to truck. It may cost a bit, not it will not be a freight charge.
I have a 1,000 lb lift on my truck and have done this several times for people- good suggestion.
Never thought of charging for it though.
Re: Metal Lathe loading challenge - richtes - 07-17-2016
Sunbelt rentals has drop bed trailers. I almost rented the dual axle (7,000 capacity) and bought a used single axle (4,000 rating) from them.
Rich