+- Woodnet Forums (https://forums.woodnet.net)
+-- Thread: Front Door ideas? (/showthread.php?tid=7321921)
Pages:
1
2
Front Door ideas? - Pirate - 08-21-2016
So, my wife wants a new front door, with some glass in it, and I was thinking of making one. Somewhere I read a post on making a veneered one with a mdf core.
Anyone know of this method, as well as other construction methods?
Or I might cut out the top 2 "raised panels" and make frames for glass. But not sure what is inside the metal door, where I need to cut out.
RE: Front Door ideas? - chips ahoy - 08-21-2016
I think you will find there is foam in there, rigid type.
Mel
RE: Front Door ideas? - MKepke - 08-21-2016
Yep, your existing metal door has likely got expanded foam in the middle.
You can buy retrofit kits to add insulated/decorative glass to plain doors: cut out opening in existing door, drop in retrofit window, etc.
I would not make anything potentially exposed to the elements out of MDF. Maybe you were thinking of MDO - MDF's weather-resistant cousin.
-Mark
RE: Front Door ideas? - Pirate - 08-21-2016
(08-21-2016, 01:25 PM)MKepke Wrote: Yep, your existing metal door has likely got expanded foam in the middle.
You can buy retrofit kits to add insulated/decorative glass to plain doors: cut out opening in existing door, drop in retrofit window, etc.
I would not make anything potentially exposed to the elements out of MDF. Maybe you were thinking of MDO - MDF's weather-resistant cousin.
-Mark
I haven't found any window kit with the right size.
Might just make inner and outter mouldings to screw together, with a groove for glass.
RE: Front Door ideas? - JGrout - 08-22-2016
What size glass are you looking for?
you can buy replacement units up to 30" wide and various heights depending on the door
all steel doors are slabs to start the openings are cut after the fact based on the glass you desire
any decent lumberyard should have the info you desire......
Joe
RE: Front Door ideas? - Pirate - 08-23-2016
If I cut out the top 2 "raised Panels" to install 1 wide window, the cut out size is 13" x 22"
Each individual top panel cut out is, 13" x 9 1/2"
RE: Front Door ideas? - JGrout - 08-24-2016
You are excluding the center mullion if you are talking about 1 window. and you can get shorter units than 13"
This page shows most options available
Joe
RE: Front Door ideas? - Dave S® - 08-24-2016
Joe knows doors
RE: Front Door ideas? - AlanS - 08-24-2016
I, too, plan to make a front door. Luckily, mine will be all glass with a 6" stile and top rail, 14" bottom rail. It will be round top. What wood? Mahagony, white oak? How do I prevent eventual warping? I could do a stave-core, but I am concerned that the 'veneer' (I guess about 1/8"-1/4") could de-laminate. There will be a storm door to protect from the direct elements. Thoughts?
RE: Front Door ideas? - Phil Thien - 08-24-2016
(08-24-2016, 03:53 PM)AlanS Wrote: I, too, plan to make a front door. Luckily, mine will be all glass with a 6" stile and top rail, 14" bottom rail. It will be round top. What wood? Mahagony, white oak? How do I prevent eventual warping? I could do a stave-core, but I am concerned that the 'veneer' (I guess about 1/8"-1/4") could de-laminate. There will be a storm door to protect from the direct elements. Thoughts?
My thinking is along the same line as yours. That is, there are pros and cons of both approaches. While the stave core may be more dimensionally stable, there do seem some risks for the average home workshop guy in the laminations of the core and the veneers.
I'm leaning towards solid white oak.