60 degree cut on table saw - Printable Version

60 degree cut on table saw - Printable Version

+- Woodnet Forums (https://www.forums.woodnet.net)
+-- Thread: 60 degree cut on table saw (/showthread.php?tid=7329008)

Pages: 1 2

60 degree cut on table saw - Jack01 - 03-26-2017

I am making a box which need couple of 60 degree cuts.
Currently I am trying to figure out to make a cut, either my brain is not working or not smart.
Looks like I have to make a jig to make this cut safely.

I would like to use table saw to make the cut.

Any ideas , suggestions?

RE: 60 degree cut on table saw - JGrout - 03-26-2017

Stand the stock up vertically and the bevel to 30* and cut.

Backer block may be required depending on the length of the cut

[img=20x400]here is an example of the setup [/img]

RE: 60 degree cut on table saw - Jack01 - 03-26-2017

JGrout;

If I understand that Bevel the saw blade to 30 degree, which will on left
Then hold the stock perpendicular to Table saw top which I can slide along the Fence.
This will give me 60 degree angle, is that correct?

RE: 60 degree cut on table saw - JGrout - 03-26-2017

yes that is correct

I also think before you make this cut you should clamp a length of wood to ride the top of the fence with the cut board sitting on the saw table.

If you do not do this the cut and your fingers could be in danger if the part tries to pull down into the saw plate opening it is much safer with the carrier to hold it in place

Joe

RE: 60 degree cut on table saw - Steve N - 03-26-2017

(03-26-2017, 06:38 PM)JGrout Wrote: I also think before you make this cut you should clamp a length of wood to ride the top of the fence with the cut board sitting on the saw table.

Very smart practice. I like using a tall box to do this, also gives me a handhold away from the blade. Depending on right or left tilt I will put the fence on the side which leaves the blade projecting out to the side of the cut, rather than into my box. That leaves your box intact and you can use it for years. Cutting precise triangles to use as support blocks for the corners make the box easier to make.

Upright cuts—for lap joints, tenons miters, or rabbets—aren’t a good job for a table saw. That is, unless you build a simple box to guide and support the workpiece. Precise cuts depend on a precise box, so take the time to build it square and sturdy. And as always, make your adjustments and mistakes using scraps before cutting precious wood.

[Image: FH14MAR_TABLSW_12.JPG]

RE: 60 degree cut on table saw - PMJ - 03-27-2017

I made this when making a flag/medal case.
[attachment=1767]

RE: 60 degree cut on table saw - JGrout - 03-27-2017

it all depends on your level of comfort so I agree,

it can be pretty simple (my solution) or you can build something a bit more elaborate

The key is to do something rather than just depend on the stock coming out of the saw on a knife point.

That is sure to fail

Joe

RE: 60 degree cut on table saw - Steve N - 03-27-2017

(03-27-2017, 09:53 AM)JGrout Wrote: The key is to do something rather than just depend on the stock coming out of the saw on a knife point.

That is sure to fail

Joe

Yep

RE: 60 degree cut on table saw - PedroOhare - 03-27-2017

Any reason not to use a tenoning jig (the ubiquitous Grizzly, Delta, Shop Fox variety) and just angle the 'tenon' to 30*?

Pedro

RE: 60 degree cut on table saw - Steve N - 03-27-2017

I've always found that a tenoning jig has limitations for stock size, but you're right, if you had small enough pieces to fit into one, it would also work. That is why I like the box, theoretically as long as you clamp firmly, the stock could extend past the edges of your box, allowing for some pretty large pieces to work.