Kraft 3' Paper Roll Dispenser/Cutter - Homemade Options? - Printable Version +- Woodnet Forums (https://forums.woodnet.net) +-- Thread: Kraft 3' Paper Roll Dispenser/Cutter - Homemade Options? (/showthread.php?tid=7339078) |
RE: Kraft 3' Paper Roll Dispenser/Cutter - Homemade Options? - Admiral - 05-02-2018 (05-02-2018, 03:41 PM)giradman Wrote: Well, came up w/ a solution - hung 14" long 1 1/2" square oak hangers under the basement stairs attached to the stringers on each side (see pic below); 3/4" holes drilled at the bottom - used some old leftover electrical conduit - the Kraft Paper roll is nearly 6' off the ground but easily reachable - now need to come up w/ an idea of cutting the paper - Dave Just dedicate a utility knife to the location, cut from middle out to each end. RE: Kraft 3' Paper Roll Dispenser/Cutter - Homemade Options? - Bill Holt - 05-02-2018 +1 on the utility knife. RE: Kraft 3' Paper Roll Dispenser/Cutter - Homemade Options? - giradman - 05-02-2018 (05-02-2018, 03:43 PM)Admiral Wrote: Just dedicate a utility knife to the location, cut from middle out to each end. (05-02-2018, 03:50 PM)Bill Holt Wrote: +1 on the utility knife. Hi Guys - I agree and have 3 or 4 utility knives, but would like a more inventive option - For example, thinking of something on hinges attached to the oak hangers and held up by magnets, then pulled down when needed to cut the paper - have a long thin piece of AL and also a bunch of hacksaw blades - will post if it happens or just use a utility knife or one of those zip cutters? Dave RE: Kraft 3' Paper Roll Dispenser/Cutter - Homemade Options? - Bob10 - 05-02-2018 (05-02-2018, 04:00 PM)giradman Wrote: Hi Guys - I agree and have 3 or 4 utility knives, but would like a more inventive option - I have to thank you for the paper idea I have always used newspaper, cardboard or ply. I have paper on order should be here next week. I am going to hang it on a dowel and makeshift some type of hooks to hold a piece of steel across the sheet that also hangs on the dowel just a bit wider to use as a straight to tear off of. I figure it will start out high on the roll and lower as the roll gets smaller RE: Kraft 3' Paper Roll Dispenser/Cutter - Homemade Options? - Gary G™ - 05-02-2018 If you rip a piece of your scrap oak with a 45* beveled edge resting on the roll, it’ll most likely be sharp enough to cut. RE: Kraft 3' Paper Roll Dispenser/Cutter - Homemade Options? - Bob10 - 05-02-2018 (05-02-2018, 04:22 PM)Gary G™ Wrote: If you rip a piece of your scrap oak with a 45* beveled edge resting on the roll, it’ll most likely be sharp enough to cut. even better, thanks RE: Kraft 3' Paper Roll Dispenser/Cutter - Homemade Options? - Cooler - 05-03-2018 (05-02-2018, 04:22 PM)Gary G™ Wrote: If you rip a piece of your scrap oak with a 45* beveled edge resting on the roll, it’ll most likely be sharp enough to cut. Melamine would be even better. A clean cut on melamine almost requires Kevlar gloves. It can be as sharp as a chisel. RE: Kraft 3' Paper Roll Dispenser/Cutter - Homemade Options? - Bob10 - 05-18-2018 well I had the best of intentions but saw this. https://www.govdeals.com/index.cfm?fa=Main.Item&itemid=44&acctid=11016 RE: Kraft 3' Paper Roll Dispenser/Cutter - Homemade Options? - Arlin Eastman - 05-18-2018 (04-22-2018, 09:07 AM)bandsaw Wrote: My roll is on a dowel between 2x4's I do the same thing. I also have a utility knife hanging by it to cut it. I think the Zippy Cutter would work even better. https://www.amazon.com/Ehdis-Snitty-Clothing-Cutting-Application/dp/B01HEQF4D0/ref=sr_1_1?ie=UTF8&qid=1526685085&sr=8-1&keywords=%22zippy+cutter https://www.amazon.com/Alvin-R53B-Cutting-Refill-Blades/dp/B0015AOQQI/ref=sr_1_2?ie=UTF8&qid=1526685085&sr=8-2&keywords=%22zippy+cutter I found the 5 Piece was just $2 more then a singe one. Go figure. RE: Kraft 3' Paper Roll Dispenser/Cutter - Homemade Options? - Stwood_ - 05-18-2018 (05-18-2018, 05:35 PM)Bob10 Wrote: well I had the best of intentions but saw this. Send one of those sections to Gman... |