Woodnet Forums
MIter gauge pivot bolt missing - Printable Version

+- Woodnet Forums (https://forums.woodnet.net)
+-- Thread: MIter gauge pivot bolt missing (/showthread.php?tid=7341174)

Pages: 1 2


MIter gauge pivot bolt missing - woodcutter100 - 07-22-2018

Need some guidance please. The center bolt (pivot) on my miter gauge for the table saw fell out. I cant find a picture to give me any reference as to how to replace it. any suggestions?


RE: MIter gauge pivot bolt missing - Stwood_ - 07-22-2018

Brand? Has it got a name on it? Brand of saw?


RE: MIter gauge pivot bolt missing - Cooler - 07-23-2018

Look here:  https://www.google.com/search?biw=1366&bih=662&tbm=isch&sa=1&ei=ciVWW-q0E8qP5wLk-o6gCw&q=miter+gauge%2C+delta+repair+parts&oq=miter+gauge%2C+delta+repair+parts&gs_l=img.3...19901.23872.0.24006.15.14.1.0.0.0.70.766.14.14.0....0...1c.1.64.img..0.1.69...0i8i30k1.0.BHzxGabso4w


RE: MIter gauge pivot bolt missing - daddo - 07-23-2018

So you have the screw but need to know how to install it?

Is this a trick question?


RE: MIter gauge pivot bolt missing - woodcutter100 - 07-23-2018

I apologize gentlemen I thought I put Delta in the header but alas not.  I don't have the screw, it was lost in the sawdust. I found one at ereplacementparts  and it has threads on one end but I can't see any threads in the miter gauge or the guide bar.
 
As far as I can tell it is part number 185 in the schematic but as usual it is not very clear.
any thoughts will help at this point
Thanks


RE: MIter gauge pivot bolt missing - fishhh4 - 07-23-2018

don't use your miter gauge . You asked ....... I have never used mine . On my sliding table yes . On saw no . Find out what thread it is . 97% of the battle.


RE: MIter gauge pivot bolt missing - handi - 07-23-2018

(07-23-2018, 04:52 PM)woodcutter100 Wrote: I apologize gentlemen I thought I put Delta in the header but alas not.  I don't have the screw, it was lost in the sawdust. I found one at ereplacementparts  and it has threads on one end but I can't see any threads in the miter gauge or the guide bar.
 
As far as I can tell it is part number 185 in the schematic but as usual it is not very clear.
any thoughts will help at this point
Thanks

I just took my Delta gauge apart to clean and tune it. The pivot bolt was difficult to remove until I realized there was a set screw too! 

It is a shoulder bolt, with a much smaller diameter threaded section than the size of the shoulder. 

On mine, the bolt actually threaded into the protractor part.


RE: MIter gauge pivot bolt missing - woodcutter100 - 07-23-2018

(07-23-2018, 06:33 PM)handi Wrote: I just took my Delta gauge apart to clean and tune it. The pivot bolt was difficult to remove until I realized there was a set screw too! 

It is a shoulder bolt, with a much smaller diameter threaded section than the size of the shoulder. 

On mine, the bolt actually threaded into the protractor part.
Thanks Ralph that helps a great deal..........


RE: MIter gauge pivot bolt missing - RogerD - 07-23-2018

Take a large magnet in your hand and pass it back and forth in the saw dust to locate the missing screw.


RE: MIter gauge pivot bolt missing - Wild Turkey - 07-25-2018

(07-23-2018, 10:10 PM)RogerD Wrote: Take a large magnet in your hand and pass it back and forth in the saw dust to locate the missing screw.

What he said.

I keep a magnet on a stick handy for just such situations.

Frequently the arbor nut to my TS
Rolleyes