+- Woodnet Forums (https://forums.woodnet.net)
+-- Thread: looking for source 1/2" Barrel nut ( Dowel nut) (/showthread.php?tid=7346510)
Pages:
1
2
looking for source 1/2" Barrel nut ( Dowel nut) - Jack01 - 02-17-2019
I am looking for source 1/2" Barrel nut ( Dowel nut)
So far I have not located yet.
I only need 4 nuts.
Once source I found the minimum order was 144 nuts.
Any suggestions.
I am looking for cross dowels for 1/2 screw.
RE: looking for source 1/2" Barrel nut ( Dowel nut) - budglo - 02-17-2019
Ace Hardware has them. Any size you want .
RE: looking for source 1/2" Barrel nut ( Dowel nut) - DaveR1 - 02-17-2019
(02-17-2019, 02:46 PM)Jack01 Wrote: I am looking for source 1/2" Barrel nut ( Dowel nut)
So far I have not located yet.
I only need 4 nuts.
Once source I found the minimum order was 144 nuts.
Any suggestions.
Are you looking for cross dowels for 1/2 screws or 1/2 in. diameter cross dowels or 1/2 in. long?
RE: looking for source 1/2" Barrel nut ( Dowel nut) - Jack01 - 02-17-2019
(02-17-2019, 03:38 PM)budglo Wrote: Ace Hardware has them. Any size you want .
Ace Hardware do not carry 1/2 threaded barrel nuts, already checked that source
RE: looking for source 1/2" Barrel nut ( Dowel nut) - Jack01 - 02-17-2019
(02-17-2019, 07:39 PM)DaveR1 Wrote: Are you looking for cross dowels for 1/2 screws or 1/2 in. diameter cross dowels or 1/2 in. long?
I am looking for cross dowels for 1/2 screw.
RE: looking for source 1/2" Barrel nut ( Dowel nut) - jasfrank - 02-17-2019
If you had a drill press and a 1/2" tap that sure wouldn't be a difficult thing to make 4 of those.
RE: looking for source 1/2" Barrel nut ( Dowel nut) - Phil Thien - 02-17-2019
Lee Valley has these:
http://www.leevalley.com/en/wood/page.aspx?cat=1,43455&p=67659
...although the cross dowels themselves look a little short.
Rockler has these:
https://www.rockler.com/heavy-duty-cross-dowel-and-bolt-8-pack
...although they're 1/2-12?
Woodcraft has these:
https://www.woodcraft.com/products/highpoint-bench-bolt-4-piece
...although they state 1/2" w/o TPI, so I don't know if they're -13 (which is typical, right?).
RE: looking for source 1/2" Barrel nut ( Dowel nut) - Aram - 02-17-2019
How about these?
Benchcrafted
RE: looking for source 1/2" Barrel nut ( Dowel nut) - Phil Thien - 02-17-2019
FWIW, I wanted something similar when I built my workbench base from LVL and found a 1/2" wing nut worked the trick. I'll confess it isn't as fancy, but it sure was less expensive and readily available. It has been 15-ish years and the bench is solid as a rock.
I just held onto one of the wings until the threads were started, didn't take any more effort than conventional cross dowels.
RE: looking for source 1/2" Barrel nut ( Dowel nut) - Jack01 - 02-17-2019
(02-17-2019, 10:00 PM)Aram Wrote: How about these?
Benchcrafted
Thanks Benchcraft will work. I just needed the barrel nuts, but I will get the set from Benchcraft.